Answer:
please find attached pdf
Explanation:
how many electrons does a neutral atom of the element oxygen have?
Answer:
8 electrons
Explanation:
Now you can figure out how many electrons, protons and neutrons Oxygen has: Atomic number (which is always the smaller of the two numbers) is 8. Hence 8 protons. Because the atom is neutral, there are also 8 electrons.
Help ASAP
Frank uses a bowling ball to demonstrate how energy can cause changes. Which
of the following actions would NOT demonstrate a change caused by applying
energy to the ball?
O He spins the bowling ball with one hand
O He rolls the bowling ball across the floor
O He holds the bowling ball in both hands
He lifts the bowling ball to place it on a shelf.
Answer:
he holds the ball in both hands
Explanation:
he's not moving the ball
How much time does it take for a spinning baseball with an angular speed of 38 rad/s to rotate through 15 degrees
Answer:
the time of motion of the ball is 6.89 ms.
Explanation:
Given;
angular speed, ω = 38 rad/s
angular distance, θ = 15 degrees
Angular distance in radian;
[tex]\theta = 15^0 \times\frac{2\pi \ rad}{360^0} = 0.2618 \ rad[/tex]
Time of motion is calculated as;
[tex]time = \frac{angular \ distance}{angular \ speed} \\\\t= \frac{\theta}{\omega} = \frac{0.2618 \ rad}{38 \ rad/s} \\\\t = 6.89 \ \times 10^{-3} \ s\\\\t = 6.89 \ ms[/tex]
Therefore, the time of motion of the ball is 6.89 ms.
What does the potential energy of an object depend on?
Answer:
The amount of gravitational potential energy an object has depends on its height and mass. The heavier the object and the higher it is above the ground, the more gravitational potential energy it holds.
Hope this helps :)
1) Li + ČI>LICI
How many atoms are in this?
Answer:
2 atoms
Explanation:
What happens to water molecules when a large quantity of thermal energy is added to water in the liquid state?
In what two ways can we increase the potential difference?
Radio telescopes are said to "listen" to space because...
1. they monitor sound waves
2. they detect radio waves
3. they detect electromagnetic waves
4. they detect only aural EM waves
Answer:
2 they detect radio waves
Identify and define Four causes of infections diseases
Answer:
Bacteria
Fungi
Viruses
Parasites
30 points!!
Electricity seems like a fundamental element in the construction of any home. However, to have electricity run into and out of a home, there must be a complete circuit. Write a brlef essay describing the minimum requirements for any electric circuit. Within your essay, describe the task for each of these elements using your lessons and experience
within this virtual lab.
At least 150 words needed.
•Most of the components that make up curcuits are conductors. Electricity flows easily thought conductors such as metal or water.Electricity does not flow easily thought insulators such as wood or rubber.
•When a battery is used to power a circuit, the circuit the current must travel from one pole of the battery to the opposite battery.
•Resisotors show the flow of Electricity throught a circuit this can prevent components of the circuit from 'brning out'. In a curcuit diagram, resistors are represented by bending lines.
What do good electrical conductors and thermal conductors have in common?
plsssssss dont answer the answer from go.ogle or i can get kicked from my school for plagiarism :(
Will mark Brainliest it's due TODAY PLEASE HELP ME
Explain how UY Scuti and J0523 are different.
Why will J1311 (the Black Widow Pulsar) eventually find itself without its companion star? How will this happen?
How did scientists determine SM0313 is the oldest star ever discovered?
What characteristics of HV2112 make it the best candidate to be classified as a Thorne-Zytkow object?
How does a star's mass determine its lifespan?
Discuss the characteristics of cool red dwarf stars, including their mass and age.
Discuss the correlation or connection between stars with a higher mass and the amount of fuel they have to work with.
How old is the sun and since its birth, how has the sun changed?
During its lifespan, what characteristics of the sun will change?
Answer:
(3rd Question about the Black Widow Pulsar)
J1311 is a fast spinning neutron star, which means it emits strong beams of radiation from it's poles.
As the beam of the pulsar sweeps across the surface of the companion star, it heats it up and blows its material outward into space, thus decreasing its mass.
Which of the following is required for U.S. citizens to travel outside the United States?
A. Consul
B. Embassy
C. Passports
D. Visas
Answer:
C.
Explanation:
Force (N) = 250
Mass (kg) = 221
Acceleration (m/s^2) = ?
Answer:
The required acceleration is [tex]a=1.1[/tex] m/s²
Explanation:
Given
Force F = 250 NMass m = 221 kgTo determine
Acceleration a = ?
We know that acceleration is produced when a force is applied to a body.
The acceleration can be determined using the formula
[tex]F = ma[/tex]
where
F is the force m is the mass a is the accelerationnow substituting F = 250 , and m = 221 in the formula
[tex]F = ma[/tex]
[tex]250 = 221 (a)[/tex]
switch the equation
[tex]221(a) = 250[/tex]
Divide both sides by 221
[tex]\frac{221a}{221}=\frac{250}{221}[/tex]
simplify
[tex]a=\frac{250}{221}[/tex]
[tex]a=1.1[/tex] m/s²
Therefore, the required acceleration is [tex]a=1.1[/tex] m/s²
what is the acceleration of an object if the object has an initial speed of 230 m/s and speeds up to 650 m/s. The time it takes for this to happen is 30 seconds
Answer:
explain this
Explanation:
all energy,potential kinetic within a specific system
a)joule
b) total energy
c) potential energy
Answer:
C
Explanation:
The potential and kinetic energy within a specific system is called the total energy of the system.
Option B is the correct answer.
Potential and Kinetic EnergyThe energy of the specific system due to its steady position is defined as the potential energy of the system.
The energy of the system which is stored due to the motion of the system is called the kinetic energy of the system.
The mechanical energy of the system is the total energy within the system including its kinetic and potential energy.
The sum of kinetic and potential energy is known as mechanical energy. An object's mechanical energy is defined as the total energy which is stored during its steady position and stored during the motion of the object.
Hence we can conclude that option B represents the correct answer for the given statement.
To know more about the potential and kinetic energy, follow the link given below.
https://brainly.com/question/21288807.
Astronomers classify galaxies by their shape. Which of the following terms describes a galaxy that looks like a round or flattened ball and contains little gas and dust between the stars?
A.
elliptical galaxy
B.
irregular galaxy
C.
No galaxies are shaped like a ball
D.
spiral galaxy
What is the law of conservation of energy?
Answer:
In physics and chemistry, the law of conservation of energy states that the total energy of an isolated system remains constant; it is said to be conserved over time. ... For instance, chemical energy is converted to kinetic energy when a stick of dynamite explodes.
Explanation:
plllllllllllssssss help will give brainiest if your get correct
Answer:
Electrical energy is transformed into heat and light energy
Explanation:
hope this helps
A 400 hp engine in a 1,600 kg car applies maximum force for 2 seconds to accelerate the car onto the
interstate. If the car moves at 8 m/s before accelerating, what is its speed after the 2 seconds of acceleration?
Answer:
I will assume that “maximum force” implies the constant application of power P = 400 hp (international) to accelerating the vehicle. The force will therefore vary with speed as the vehicle accelerates. I will also assume that all engine energy goes into accelerating the vehicle, rather than rotating elements like its wheels.
In this case the 400 hp (equivalent to 298,280 watts) is applied for time t = 2 seconds. Therefore the kinetic energy of the vehicle is increased by:
ΔKE=Pt=(298,280)(2)=596,560 joules.
The initial kinetic energy is:
KEinitial=12mv2
=(0.5)(1600)(82)=51,200 joules.
Therefore final kinetic energy is:
KEfinal=KEinitial+ΔKE
=51,200+596,560
=647,760 joules
Therefore final vehicle velocity can be found:
KEfinal=12mv2
v=2KEfinalm−−−−−−−−√
=(2)(647,760)1600−−−−−−−−−−−√
= 28.455 m/s
Explanation:
A brick has a density of 21.6 g/cm3 and a mass of 15.4 g. What is the volume of
the brick?
4. What will happen to the amount of kinetic energy if an object's mass
decreases?
A. The kinetic energy will increase I
B. The kinetic energy will decrease
C. The kinetic energy will remain constant
Which statement best describes the atoms of elements that form compounds by covalent bonding?
They share electrons between them.
They have a large difference in valence electron number
They have a large difference in atomic mass.
They are in the same period in the periodic table.
Answer:
they share electrons between them.
Explanation:
taking the test rn lol i think its right
Why is oxygen more chemically reactive than nitrogen?
A. Oxygen needs to gain only 2 electrons to have a full octet, while
nitrogen needs to gain 3.
B. Oxygen needs to gain only 2 electrons to have a full octet, while
nitrogen needs to lose 3.
C. Oxygen needs to lose only 2 electrons to have a full octet, while
nitrogen needs to lose 3.
D. Oxygen needs to lose only 2 electrons to have a full octet, while
nitrogen needs to gain 3.
Oxygen is more chemically reactive than nitrogen because Oxygen needs to gain only 2 electrons to have a full octet, while nitrogen needs to gain 3. The correct option is A.
What are electrons?The electrons are the spinning objects around the nucleus of the atom of the element in an orbit.
Valence electrons are the electrons present in the outermost shell of an atom. They can easily be determined by the number of valence electrons in an atom by looking at the specific group in the periodic table.
The fewer number of electrons in the valance shell, the more reactive is the element.
Oxygen needs to gain only 2 electrons to have a full octet, while nitrogen needs to gain 3.
Thus, Oxygen is more chemically reactive than nitrogen.
Then the correct option is A.
Learn more about electrons.
https://brainly.com/question/1255220
#SPJ5
Answer:
A
Explanation:
Apex built different
A passive continental margin has a ____, while an active margin does not.
O A. continental rise
O B. continental slope
O C. continental duct
O D. continental shelf
A passive continental margin has a continental rise, while an active margin does not. Therefore, option A is correct.
What is passive continental margin?Where there is no plate border to mark the transition from land to sea, this is known as a passive continental margin.
A good example is the east coast of the United States, where the plate boundary is a distance from the shore along the mid-Atlantic ridge. Little geological activity occurs along passive borders.
Volcanoes, mountain belts, and earthquakes all identify active margins. They lack a continental uplift and an abyssal plain, in contrast to passive margins.
The Pacific and North American Plate boundaries are visible along the west coast of the United States, which is an example of an active margin. Where there is no plate border to mark the transition from land to sea, this is known as a passive continental margin.
Thus, option A is correct.
To learn more about the passive continental margin, follow the link:
https://brainly.com/question/11505884
#SPJ5
Whats is the resistance of a bulb with a current of 60a in a circuit with a 12v battery
Answer:
60a in a circuit with a 12v battery
Explanation:
60a in a circuit with a 12v battery
Can anyone help with this physics question
C + H2 ----------> CH4
Answer:
yes
.......................
Answer:
C + 2H2 -----> CH4
A 50 kg bumper car with a 40 kg child and it is at rest when a 60 kg child in her own bumper car slams into it the collision last point1 seconds and the rubber bumpers are perfectly bouncy with no heating from the collision what is the force experienced by the first car
Answer:
F = 99 v₂₀
v₂₀ = 1 m / s, F = 99 N
Explanation:
In this exercise it is asked to find the force during the collision, for this we use the relationship between the momentum and the momentum of car 1
I = Δp
F t = p_f- p₀
F t = m (v_f -v₀) (1)
We must find the final speed of car 1, for this we define a system formed by the two cars, in this case the forces during the collision are internal and the moment is conserved
initial instant. Before the crash
p₀ = 0 + m₂ v₂₀
final instant. After the crash
p_f = m₁ v₁ + m₂ v_{2f}
the moment is preserved
p₀ = p_f
m₂ v₂₀ = m₁ v_{1f} + m₂ v_{2f} (2)
m₂ (v₂₀ - v_2f}) = m₁ v_{1f}
as the collision is elastic the kinetic energy is also conserved
K₀ = K_f
½ m₂ v₂₀² = ½ m₁ v_{1f}² + ½ m₂ v_{2f}²
m₂ (v₂₀² -v_{2f}²) = m₁ v_{1f}²
let's write our system of equations, using
a² - b² = (a + b) (a-b)
m₂ (v₂₀ - v_{2f}) = m₁ v_{1f}
m₂ (v₂₀ -v_{2f}) (v₂₀ + v_{2f}) = m₁ v_{1f}²
to solve we divide the equations
v₂₀ + v_{2f} = v_{1f}
with this we substitute in equation 2 and find the speed of each car, in this case we need the speed of car 1
m₂ v₂₀ = m₁ v_{1f} + m₂ (v_{1f}-v₂₀)
2m₂ v₂₀ = (m₁ + m₂) v_{1f}
v_{1f} = [tex]\frac{2m_2}{m_1+m_2} v_{2o}[/tex]
We substitute in the drive ratio of car 1
F t = m (v_f -v₀)
F = m₁ (\frac{2m_2}{m_1+m_2} v_{2o} - 0) / t
F = [tex]\frac{2m_1 m_2 }{m_1+m_2} \ \frac{v_{2o}}{t}[/tex]
the mass of each car is the mass of the car plus the mass of the boy
m₁ = 50 +40 = 90 kg
m₂ = 50 +60 = 110 kg
time is t = 1
we substitute the values
F = [tex]\frac{ 2\ 90 \ 110}{90+110} \ \frac{v_{2o}}{1}[/tex]2 90 100/90 + 110 vo2 / 1
F = 99 v₂₀
The value of the initial velocity of car 2 is not indicated in the problem, if this velocity is known it can be included and the force value is obtained, suppose that the initial velocity v₂₀ = 1 m / s
F = 99 N
The number of protons plus the number of neutrons in an atom is equal to its
Answer:
Atomic Mass
Explanation: