Answer:
Explanation:
If you look at the chemistry behind most brake fluid, it comes from the combination of various types of glycols, which are basically a mixture of non-petroleum and other alcohol-based fluids. After a mixing process, the chemical name gets shortened to “polyglycol”. In addition, there are also high-grade silicone-based fluids, which cannot be mixed with any other type of fluid. So whether it's used in the brake or clutch system, it's important to understand the differences between these common types of brake fluid.
The brake fluid must maintain specific properties. Our brakes can get hot, sometimes up to 1200 degrees, so the fluid needs a high boiling point. Also, because our vehicles experience seasons just as we do, it’s important to have low freezing point as well. On top of maintaining both extremes, it's designed not to damage any rubber components in the brake system.
As a result, the chemical properties found in most brake fluids can permanently dull or damage paint. So be sure to handle with care and be quick to clean any accidental overspills. Brake fluid is hydroscopic, meaning it has a natural tendency to absorb moisture. And over enough time the added moisture can result in corrosion build up or a decreased boiling point. It’s never a bad idea to change your brake fluid every couple of years and try not to leave your reservoir cap off any longer than needed
Answer: high operation temperatures, good low-temperature and viscosity-temperature properties, physical and chemical stability, protection of metals from corrosion, inactivity with respect to mechanical rubber articles, and lubricating effect
Hope this helps
Se realiza un experimento en el que se mide el alargamiento de un muelle debido a la acción de una pesa; se trata de comprobar la ley de Hooke. Los datos que se han obtenido son: Medición 1 2 3 4 5 Alargamiento 42.0 48.4 51.3 56.3 58.6 Masa 2 4 6 8 10 El coeficiente de determinación es:
Answer:
m = 1,975 m / kg , b = 38.05 m
Explanation:
In this experiment, the elongation is plotted against the applied mass
getting a straight line
y = m x + b
where b would be the initial length of spring let's calculate the slope for which we use two well separated points
m = (56.3 -48.4) / (8 - 4)
m = 1,975 m / kg
the equation remains
y = 1,975 x + b
for x = 2 kg y = 42.0 m
we substitute in the equation
42 = 1,975 2 + b
b = 42 - 3.95
b = 38.05 m
A tuning fork is vibrating the air around it. What best describes the waves produced by the tuning fork?
Answer:
The water particles move in the same direction as the vibrating source of the sound wave. ... What best describes the waves produced by the tuning fork? mechanical, because the vibrating tuning fork makes air molecules around it vibrate. A wave is produced in a Slinky as shown.
Explanation:
Answer:
mechanical, because the vibrating tuning fork makes air molecules around it vibrate
Explanation:
People often think that Galileo dropped two objects of dramatically different mass off of the Leaning Tower of Pisa that both hit the ground at the same time. Explain why in reality this was most likely not true.
Answer: because of air resistance. See explanation for further details.
Explanation: Galileo performed an experiment to proof that the time of descent of two different masses is independent of time.
But in reality this is most likely not true because of air resistance and other fluid frictional effects in consideration.
If the experiment is performed in a vacuum, it will always be true that time is independent of masses of two falling objects.
what is web browser
Answer:
A web browser is a software application for accessing information on the World Wide Web
Answer:
web browser (commonly referred to as a browser) is a software application for accessing information on the World Wide Web. When a user requests a web page from a particular website, the web browser retrieves the necessary content from a web server and then displays the page on the screen.
Explanation:
Which objects would sink in honey, which has a density of 1.4 g/cm³? Check all that apply.
Answer:
any object that has density more than 1.4
Explanation:
The object that has density more than 1.4 is denser than the honey
Explain two applications of resonance
PLEASEEEE HELP ME!
Answer:
in physics, resonance is a phenomenon in which a vibrating system or external force drives another system to oscillate with greater amplitude at specific frequencies. example a familiar example is a playground swing, which acts as a pendulum.
hope this helped!
You get in your car to drive to school at 7:33 am and drive 10 miles north at a constant speed until 7:45
am, when you realize you left your homework on the kitchen table. You turn around and drive 10 miles
south back to your house and retrieve your homework at 8:00 am. You get back in the car and drive 15
miles north to school at a constant speed arriving at school at 8:29 am sharp, just in time to make it
before the bell rings.
e
Answer:
5.) 16.8 m/s
6.) 16.1 mph
7.) Moving fast.
Explanation:
5.) From the question, the total time will be:
7:33 am to 7:45 am = 12 minutes
As the car turns around,
7 : 45 am to 8 : 00am = 15 minutes
As you get back in the car and drive 15
miles north to school at a constant speed arriving at school at 8:29 am
8:00am to 8:29 am = 29 minutes
Total time = 12 + 15 + 29 = 56 minutes
Convert the minutes to second by multiplying the result by 60
Total time = 56 × 60 = 3360 seconds
Total distance covered will be
10 miles + 10 miles + 15 miles = 35 miles
Convert mile to meter by multiplying the result by 1609.344
35 × 1609.344 = 56327.04
Speed is a scale quantity. It only involves magnitude but no direction.
Average speed = total distance/total time
Average speed = 56327.04/3360
Average speed = 16.764 m/s
6.) Velocity = displacement/time
Velocity is a vector quantity. We will consider both the magnitude and direction
Total displacement = 10 miles - 10 miles + 15 miles = 15 miles.
Total time = 56 minutes
Convert minutes to hours by dividing it by 60
Total time = 56/60 = 0.93 hours
Substitute the time and displacement into the formula
Velocity = 15/0.93 = 16.07 mph
7.) . If you looked at your speedometer on your drive to school and it read 30mph, this value describes you move with a fast speed.
What is a resistor? A. a light bulb B.a switch C. a battery
Answer:
A resistor is a battery
Answer:
The answer is A
Explanation:
A resistor is a light bulb because it is the flow of an electric current in an electric circuit.
An electric kettle is rated at 2kW. How much energy is transferred in 30s?
Answer : 60,000 Joule
✑ Given :
Power = 2 KW = 2 × 1000 W = 2000 W ( since 1 KW = 1000 W )Time taken = 30 seconds✑ To find :
Energy☞ Solution :
✾ Energy = Power × Time ✾
= 2000 × 30
= 60,000 Joule
Hope I helped!
ツ Have a wonderful day / night !♡
~TheAnimeGirl ♪
Answer:
60,000 Joules
Explanation:
GIVEN:
Power = 2kW = 2000 W
Time = 30 sec
REQUIRED:
Energy = ?
SOLUTION:
Power = Energy / Time
Making Energy the subject of formula
Energy = Power × Time
E = 2000 W × 30 s
E = 60,000 Joules
Which of the following technologies is based on the work of Subrahmanyan Chandrasekhar? A. Undersea fiber optic communications cables B. An orbiting observatory to detect X-rays from space objects C.Computer models to predict the effects of climate change D. Radar to detect the movement of storms
Answer:the answer is B
Explanation:
APE X
The technology that is based on the work of Subrahmanyan Chandrasekhar is an orbiting observatory to detect X-rays from space objects, therefore the correct option is B.
What is Chandrasekhar's limit?Chandrasekhar's limit is a type of maximum limited value that is used to define the maximum mass of a white dwarf star. The generally internationally considered value of the Chandrasekhar limit is about 1.44 times the mass of the sun which is approximately 2.765×10³⁰ kg.
In other words, one can say that Chandrasekhar limit is the maximum value that can attain 1.44 times the solar mass.
In other words, one can say that star with a mass more than 1.44 times that of the Sun does not form a white dwarf but continues to collapse, finally forming a neutron star
An orbiting observatory to detect X-rays from space objects is based on the principle of Chandrasekhar's limit. The correct option is B.
Learn more about Chandrasekhar's limit from here
https://brainly.com/question/7259500
#SPJ2
what is the wavelength of radio waves transmitted by an FM station at 90MHz where 1M=10^6, and speed of radiowave is 3*10^8m/s
Answer:
λ = 3.33 m
Explanation:
Given:
Frequency = f = 9 × 10⁷ Hz
Speed = v = 3 × 10⁸ m/s
Required:
Wavelength = λ = ?
Formula:
v = fλ
Solution:
Putting the givens in the formula
v = fλ
λ = [tex]\frac{v}{f}[/tex]
λ = [tex]\frac{3*10^8}{9*10^7}[/tex]
λ = 0.33 × 10¹
λ = 3.33 m
what happens to the moleclues within a gas when the gas Condeenses
Help what is the answer
Answer:
C
Explanation:
[tex]F=k\dfrac{Q_1Q_2}{r^2}= \\\\(8.99 \times 10^9)\dfrac{(-2\times 10^{-4})(8\times 10^{-4})}{0.3^2}\approx 1.6\times 10^4 N[/tex]
Hope this helps!
You are on an interstellar mission from the Earth to the 8,7 light-years distant star Sirius. Your spaceship can travel with 70% the speed of light and has a cylindrical shape with a diameter of 6 m at the front surface and a length of 25 m. You have to cross the interstellar medium with an approximated density of 1 hydrogen atom/m3 (a) Calculate the time it takes your spaceship to reach Sirius. (b) Determine the mass of interstellar gas that collides with your spaceship during the mission. Note:use 1,673x 10^-27 kg as proton mass
Answer:
Time = 12.43 years
Mass = 4.71.43kg
Explanation:
Given the following :
Distance = 8.7 light years
Speed = 70% the speed of light
Diameter = 6m
Lengtg = 25m
Density = 1 hydrogen atom/m^3
Mass of proton(Me) = 1.673x 10^-27
A.) time it takes your spaceship to reach Sirius :
From the relation: Speed = (distance / time)
Time = distance / speed
Time = (70/100) × 1 light year
Distance = 8.7 light years
Time = 8.7 / 0.7 = 12.4285 years
Time = 12.43 years
B.) Mass of inter-stellar gas that collides with the spaceship can be calcuted by finding the product of the surface area of the cylindrical space ship and the mass of proton.
That is ;
surface area * mass of proton
Surface area of a cylinder = 2πrh + πr^2×Me
= 2πrh + Me×πr^2)
=( 2 × 22/7 × 3 × 25) + (22/7 × 3^2 × 1.673 * 10^-27)
= 2× 235.714 + 28.285) × 1.673 * 10^-27
= 471.428 + 47.31 * 10^-27
= 471.428 + 4.73 × 10^-26
= 4.71.43kg approximately
When salt is added to the water what happens to the surface?
Answer:
it increases the surface tension of the water
A 1.2 m steel rod moves through a uniform magnetic field of 0.020 T at 30 m/s. What emfis induced between the two ends of the steel rod?
0.36 V
0.50 V
0.60 V
0.72 V
Answer:
0.50v
Explanation:
Now EMF is induced when there is motion of a conductor in an electric field. Michael Faraday in the annals of scientific history discovered this.
This is expressed mathematically as;
E = Magnetic field / t
but t = d/ v; d- distance, v-velocity, time
Hence E = magnetic field/ d/v
= Magnetic field× v/ d
= 0.02×30/ 1.2= 0.5
A device has power -2 D . The device is
a.A convex lens of focal length 50 cm
b.A concave lens of focal length 50 cm
c.A convex lens of focal length 2 m
d.A concave lens of focal length 2 m
Answer:
b.
Explanation:
-vesign shows the lens is CONCAVE
f=1/power
Diagram shows the heating
curve for 0.5 kg heated by a
100 W immersion heater. What
is the specific heat capacity of
the liquid?
Answer: 35
Explanation:
Given the following :
M = 0.5 kg
Power of heater = 100W
From the graph ;
Time (t) = 7seconds
Change in temperature(Dt) = t2 - t1
Where t2 = 70°C, t1 = 30°C
Dt = (70 - 30)°C = 40°C
Recall Q = iVt
IV = power
Q = mcDt
c = specific heat capacity of liquid
mcDt = ivt
mcDt = power × t
0.5 × c × 40°C = 100 × 7
20°C × c = 700 J
c = 700 J/ 20°C
c = 35 J / kg°C
A scanning tunneling microscope is used to measure small changes in height of a surface by detecting changes in the tunneling current between the tip and the surface. The current is proportional to the tunneling coefficient (ie. I = const * T) which follows the general equation for tunneling through a square well , with C dependent on the molecule and L is the distance. The transmission coefficient at one point is T = 0.01, what is the relative current if the distance is increased from L to 5L? We are interested in I(5L)/I(L). (Note: there may be more information provided than you need to solve the problem.)
Answer:
[tex]\mathbf{\dfrac{I(5l)}{I(l) } =10^{-8}}[/tex]
Explanation:
We are being told that the current is proportional to the tunneling coefficient[tex]I(l) = I_0 e^{-2kl}[/tex] ;
where l = distance between the tip and the surface.
Let [tex]I(l) = I_0 e^{-2kl}[/tex] ------------ equation (1)
and [tex]I(5l) = I_0 e^{-2k(5l)}[/tex] ------------ equation (2)
Dividing equation (2) by (1); we have :
[tex]\dfrac{I(5l)}{I(l) } = \dfrac{I_0 e^{-2k(5l)}}{ I_0 e^{-2kl}}[/tex]
[tex]\dfrac{I(5l)}{I(l) } =e^{-2k(5-1)l}[/tex]
[tex]\dfrac{I(5l)}{I(l) } =(e^{-2kl})^4[/tex]
where ;
[tex](e^{-2kl})[/tex] represents the transmission coefficient T = 0.01
Thus; replacing the value for 0.01;we have;
[tex]\dfrac{I(5l)}{I(l) } =0.01^4[/tex]
[tex]\mathbf{\dfrac{I(5l)}{I(l) } =10^{-8}}[/tex]
A 4.0 kg block is initially at rest on a frictionless, horizontal surface. The block is moved 8.0 m by the application of a constant 10.0 N horizontal force. If the block slides into a fixed horizontal spring and comes to rest when the spring is compressed a distance of x=0.25m. Determine the spring constant of the fixed horizontal spring. Show all formula with substitutions and units.
Answer:
k = 2560 N/m
Explanation:
To find the spring constant, you take into account that all the kinetic energy of the block becomes elastic potential energy in the spring, when the block compressed totally the spring:
[tex]K=U\\\\\frac{1}{2}mv^2=\frac{1}{2}kx^2[/tex]
m: mass of the block = 4.0kg
v: velocity of the block just before it hits the spring
x: compression of the spring = 0.25m
k: spring constant = ?
You solve the previous equation for k:
[tex]k=\frac{mv^2}{x^2}[/tex] (1)
Then, you have to calculate the velocity v of the block. First, you calculate the acceleration of the block by using the second Newton law:
[tex]F=ma[/tex]
F: force over the block = 10.0N
a: acceleration
[tex]a=\frac{F}{m}=\frac{10.0N}{4.0kg}=2.5\frac{m}{s^2}[/tex]
With this value of a you can calculate the final velocity after teh block has traveled a distance of 8.0m:
[tex]v^2=v_o^2+2ad[/tex]
vo: initial velocity = 0m/s
d: distance = 8.0m
[tex]v=\sqrt{2ad}=\sqrt{2(2.5m/s^2)(8.0m)}=6.32\frac{m}{s}[/tex]
Now, you can calculate the spring constant by using the equation (1):
[tex]k=\frac{mv^2}{x^2}=\frac{(4.0kg)(6.32m/s)^2}{(0.25m)^2}=2560\frac{N}{m}[/tex]
hence, the spring constant is 2560 N/m
An object with more mass has more kinetic energy than an object with less
mass, if both objects are moving
OA) at the same speed
OB) in the same direction
OC) in opposite directions
Explanation:
The kinetic energy of an object is given in terms of its mass and object as :
[tex]K=\dfrac{1}{2}mv^2[/tex]
An object with more mass has more kinetic energy. An object with less mass, if both objects are moving at the same speed, in opposite directions, will have less kinetic energy. The square of v will give positive number.
Why did the Founding Fathers want to include a bill of rights in the U.S.
Constitution?
A. To ensure that the government couldn't take away the individual
rights of citizens
B. To provide future generations a way to amend, or change, the
Constitution
C. To allow states to write and approve their own state constitutions
D. To give state governments more power than the federal
government
Answer:
Its A
Explanation:
Thats because federalists wanted to take away rights. But the fathers wanted to definitely ensure that each person had equal rights and liberty.
Earth receives some of the Sun's energy in the form of heat and light.
What type of energy does heat and light from the Sun begin as?
O A) nuclear
OB) chemical
OC) electrical
OD) mechanical
Answer:
a) nuclear
Explanation:
A 1.00 kg block of ice, at -25.0°C, is warmed by 35 kJ of energy. What is the final temperature of the ice?
Answer:
-8.4°C
Explanation:
From the principle of heat capacity.
The heat sustain by an object is given as;
H = m× c× (T2-T1)
Where H is heat transferred
m is mass of substance
T2-T1 is the temperature change from starting to final temperature T2.
c- is the specific heat capacity of ice .
Note : specific heat capacity is an intrinsic capacity of a substance which is the energy substained on a unit mass of a substance on a unit temperature change.
Hence ; 35= 1× c× ( T2-(-25))
35= c× ( T2+25)
35 =2.108×( T2+25)
( T2+25)= 35/2.108= 16.60°{ approximated to 2 decimal place}
T2= 16.60-25= -8.40°C
C, specific heat capacity of ice is =2.108 kJ/kgK{you can google that}
To solve this we must be knowing each and every concept related to energy. Therefore, -8.40°C is the final temperature of the ice.
What is energy?In physics, energy is the capacity to accomplish work. It can be potential, kinetic, temperature, electrical, chemical, radioactive, or in other forms.
There is also heat and work—energy inside the process of being transferred through one body to the other. Energy is always classified according to its type once it has been transmitted. As a result, heat transported could become thermal energy, whereas labor done may emerge as mechanical energy.
H = m× c× (T2-T1)
35= 1× c× ( T2-(-25))
35= c× ( T2+25)
specific heat capacity of ice is =2.108 kJ/kgK
35 =2.108×( T2+25)
( T2+25)= 35/2.108= 16.60°
T2= 16.60-25= -8.40°C
Therefore, -8.40°C is the final temperature of the ice.
To know more about energy, here:
https://brainly.com/question/29763772
#SPJ2
PLEASE HELP!!!!!
When describing image formation for plane mirrors, what is an important rule
to remember about light rays?
Answer: The image formed by a plane mirror is always virtual (meaning that the light rays do not come from the image), upright and of the same shape and size as the object it is reflecting.
Answer: B. The angle when it leaves is the same as the angle when it hits
Explanation:
Apex
In simple terms describe diffraction, refraction and reflection. Give examples for each.
Answer:
Refraction is the bending of life an example would be how when you put a straw in a glass and it looks like the straw gets detached from itself. Reflection is when light bonces off of something an example would be a mirror.
Explanation:
The way a mirror works is the light you see bounces off of the glass and gives your optical sensors the vision of what the glass reflected.
Answer:
Diffraction , refraction and reflection all are property of light that shows its wave nature.
Explanation:
What is diffraction?When a light ray passes through a narrow single slit , the superposition of secondary wavelets produced by the same source , is called diffraction.
Example ; Single slit experiment in which the diffraction shows maxima and minima .
What is refraction ?The banding of light due to variation in the speed of light when it travels from one medium to another is called refraction.
Example; Divergence or convergence by lenses.
What is reflection ?The bouncing back of light from a surface is called reflection.
Example : Mirrors.
Hence all the given topics are explained.
https://brainly.com/question/10582210
#SPJ2
Ed biked home from school in 400 seconds. His home is located 2000 m south of the school. What was his velocity?
[tex]answer = 5 \: \: metre \: per \: second\\ distance = 2000 \: m \\ time = 400 \: seconds \\ velocity = \: \frac{distance \:t ravelled}{time \: taken} \\ \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: = \frac{2000}{400} \\ \: \: \: \: \: \: \: \: \: = 5 \: metre \: per \: second \\ hope \: it \: helps[/tex]
Density changes are responsible for which method of thermal energy transfer.
Answer:
convection
Explanation:
because in convection, molecules move with heat(i.e wind). So, when molecules move to another place, the mass will be reduce and the density will change
A student claims that water's polarity is the reason it has a high specific heat. What method could the student use to test his claim? Perform research to see if other polar molecules have high specific heat Measure how much energy it takes to increase the temperature of water by one degree Mix water with an acid and test the new specific heat Determine how dissolving salt in water affects the specific heat
Answer:
B
Explanation:
The method used by the student to test his claim is determine how dissolving salt in water affects the specific heat. The correct option is fourth.
What is specific heat?The specific heat is the amount of heat required to change the temperature by 1°C. It is denoted by C.
A student claims that water's polarity is the reason it has a high specific heat.
Polarity is determined by the salt dissolved in water. So, to determine how dissolving salt in water affects the specific heat is best method.
Thus, the fourth option is correct.
Learn more about specific heat.
https://brainly.com/question/11297584
#SPJ5
A ramp is a simple machine called the
a. wedge
b. pulley
c. inclined plane
d. lever
Answer:
Inclined Plane is the answer
Answer:
Inclined plane
Explanation:
It is called Inclined plane since it is a flat surface at an angle.