Answer:
No, it is not a periodic Signal
Explanation:
No, it is not a periodic Signal
This signal is repeating itself with the fixed on and off values but the major point to note here is that is this signal repeating after a fixed length of time every time. No, such information is provided in the question and hence, this signal cannot be termed as periodic.
For a bronze alloy, the stress at which plastic deformation begins is 284 MPa and the modulus of elasticity is 106 GPa. (a) What is the maximum load that can be applied to a specimen having a cross-sectional area of 310 mm2 without plastic deformation? (b) If the original specimen length is 120 mm, what is the maximum length to which it may be stretched without causing plastic deformation?
Answer:
a) the maximum load is 88,040 N
b)
the maximum length to which the specimen may be stretched is 0.12032148 mm
Explanation:
Given the data in the question;
the stress at which plastic deformation begins σ = 284 MPa = 2.84 × 10⁸ Pa
modulus of elasticity E = 106 GPa = 1.06 × 10¹¹ Pa
a)
Area A = 310 mm² = 310 × 10⁻⁶ m ( without plastic deformation )
now, lets consider the equation relating to stress and cross sectional area.
σ = F / A₀
hence, maximum load F = σA₀
so we substitute
F = (2.84 × 10⁸) × (310 × 10⁻⁶)
F = 88,040 N
Therefore, the maximum load is 88,040 N
b)
Initial length specimen l₀ = 120 mm = 120 × 10⁻³ m
using engineering strain, ε = (l₁ - l₀)/l₀
Also from Hooke's law, σ = Eε
so from the equation above;
l₁ = l₀( ε + 1 )
l₁ = l₀( σ/E + 1 )
so we substitute
l₁ = (120 × 10⁻³)( (2.84 × 10⁸)/(1.06 × 10¹¹)) + 1 )
l₁ = (120 × 10⁻³) ( 1.002679 )
l₁ = 0.12032148 mm
Therefore, the maximum length to which the specimen may be stretched is 0.12032148 mm
When an arbitrary substance undergoes an ideal throttling process through a valve at steady state, (SELECT ALL THAT APPLY) inlet and outlet mass flowrates will be equal. inlet and outlet specific enthalpies will be equal. inlet and outlet pressures will be equal. inlet and outlet mass flowrates will be equal. inlet and outlet specific enthalpies will be equal. inlet and outlet temperatures will be equal.
Answer:
15x
Explanation:
Using a small cube as a representative volume of material, illustrate graphically all the six independent components of strains that determine the state of strain in the volume of material that is enclosed by the cube. Indicate in your schematics, the change in shape produced by each of the normal strain and shear strain components.
Answer:
Attached below
Explanation:
Attached below is the schematic diagram of a small cube representing volume of material and all the six independent components of strains that will determine the state of strain
Note : Attached below is a free hand diagram of the cube indicating the six independent components of strains and a screen shot of the change in shape produced by each of the normal strain and shear strain components
( drawn with online tools )
Calculate the relative pipe roughness for a plastic pipe with absolute roughness 0.0025 mm and internal diameter of pipe is 0.157 inches.
Answer:
6.27 × 10⁻⁴
Explanation:
Relative roughness, k = ε/D where ε = absolute roughness = 0.0025 mm and D = internal pipe diameter = 0.157 in = 0.157 × 25.4 mm = 3.9878 mm
So, k = ε/D
= 0.0025 mm/3.9878 mm
= 6.27 × 10⁻⁴
The relative pipe roughness for a plastic pipe will be:
"6.27 × 10⁻⁴".
Relative roughness of pipeAccording to the question,
Absolute roughness, ε = 0.0025 mm
Internal pipe diameter, D = 0.157 in or,
= 0.157 × 25.4 mm
= 3.9878 mm
We know that,
The relative roughness be:
→ k = [tex]\frac{Absolute \ roughness}{Diameter}[/tex]
or,
k = [tex]\frac{\varepsilon }{D}[/tex]
By substituting the above values,
= [tex]\frac{0.0025}{3.9878}[/tex]
= 6.27 × 10⁻⁴
Thus the above approach is correct.
Find out more information about diameter will be:
https://brainly.com/question/13100709
How should backing plates, struts, levers, and other metal brake parts be cleaned?
Answer: Cleaning of mechanical parts is necessary to remove contaminants, and to avoid clogging of wastes which could restrict the functioning of the machine.
Explanation:
There are different agents used for cleaning different machine instruments to prevent their corrosion and experience proper cleaning.
Backing plates must be dry cleaned using a cotton cloth to remove the dirt, dust or any other dry contaminant.
Struts can be wet cleaned by applying alcoholic solvent.
Levers can be cleaned using a mineral spirit.
Metallic plates can be cleaned using water based solution or water.
The criminal and traffic code requires that a driver must have a valid driver's license in his/her
immediate possession at any time when operating a motor vehicle.
True
False
Answer:
true
Explanation:
the answer is true because if u don't have a valid license when operating a vehicle and you get pulled over you will get in trouble i know this because my parents got in trouble for it once
List six possible valve defects that should be included in the inspection of a used valve?
Answer:
Valvular stenosis , Valvular prolapse , Regurgitation,
Explanation:
A cylindrical specimen of this alloy 12 mm in diameter and 188 mm long is to be pulled in tension. Assume a value of 0.34 for Poisson's ratio.Calculate the stress (in MPa) necessary to cause a 0.0105 mm reduction in diameter.
This question is incomplete, the missing image in uploaded along this answer below.
Answer:
The required stress is 200 Mpa
Explanation:
Given the data in the question;
diameter D = 12 mm = 12 × 10⁻³ m
Length L = 188 mm = 188 × 10⁻³ m
Poisson's ratio v = 0.34
Reduction in diameter Δd = 0.0105 mm = 0.0105 × 10⁻³ m
The transverse strain will;
εˣ = Δd / D
εˣ = -0.0105 × 10⁻³ / 12 × 10⁻³ m
εˣ = -0.00088
The longitudinal strain will be;
[tex]E^z[/tex] = - ( εˣ / v )
[tex]E^z[/tex] = - ( -0.00088 / 0.34 )
[tex]E^z[/tex] = - ( - 0.002588 )
[tex]E^z[/tex] = 0.0026
Now, Using the values for strain, we get the value of stress from the graph provided in the question, ( first image uploaded below.
From the graph, in the Second image;
The stress is 200 Mpa
Therefore, The required stress is 200 Mpa
For maximum safety, an electrician should learn
A. all OSHA standards and requirements by heart.
B. to perform most tasks with one hand.
c. to perform tasks in low light situations.
D. every NEC code by heart.
Answer:A
Explanation:The minimum level of education required to become an electrician is a high school diploma or equivalency degree, like the General Education Diploma (GED). This educational step is important on the journey to becoming an electrician because the high school curriculum covers the basic principles used on the job.
Wattage is:
Select one:
a.
A measure of the total electrical work being performed per unit of time.
b.
Expressed as P = R × A.
c.
Both A and B.
d.
Neither A nor B.
Answer:
c.Both A and B.
Explanation:
the wattage is c and d
A thick steel slab ( 7800 kg/m3 , c 480 J/kg K, k 50 W/m K) is initially at 300 C and is cooled by water jets impinging on one of its surfaces. The temperature of the water is 25 C, and the jets maintain an extremely large, approximately uniform convection coefficient at the surface. Assuming that the surface is maintained at the temperature of the water throughout the cooling, how long will it take for the temperature to reach 50 C at a distance of 25 mm from the surface
Answer:
1791 secs ≈ 29.85 minutes
Explanation:
( Initial temperature of slab ) T1 = 300° C
temperature of water ( Ts ) = 25°C
T2 ( final temp of slab ) = 50°C
distance between slab and water jet = 25 mm
Determine how long it will take to reach T2
First calculate the thermal diffusivity
∝ = 50 / ( 7800 * 480 ) = 1.34 * 10^-5 m^2/s
next express Temp as a function of time
T( 25 mm , t ) = 50°C
next calculate the time required for the slab to reach 50°C at a distance of 25mm
attached below is the remaining part of the detailed solution
5. The pin support at A allows _______. Select the one that applies. (a) displacement in the x direction (b) rotation about its central axis (c) displacement in the y direction (d) none of the above 6. The support at B does not allow _______. Select the one that applies. (a) displacement in the x direction (b) rotation about its central axis (c) displacement in the y direction
Answer: Diagram associated with your question is attached below
5) B
6) C
Explanation:
5) The pin support at A allows ; Rotation about its central axis
This is because pin supports does not allow the translation of its structural member in any direction i.e. y or x but only rotation about its axis
6) The support at B does not allow displacement in y direction
This is because roller support allows displacement only in the direction that they are situated and in this case it is the x - direction
Which option identifies the step of the implementation phase represented in the following scenario?
A company in the gaming industry decides to integrate movement controls in its newest hardware release. It sends an online survey to interactive gamers to identify their highest priorities.
establishing a process and budget
using communication tools
building and assembling a team
setting up a change order process
Answer:
Which option identifies the step of the implementation phase represented in the following scenario?
A company in the gaming industry decides to integrate movement controls in its newest hardware release. It sends an online survey to interactive gamers to identify their highest priorities.
establishing a process and budget
using communication tools
building and assembling a team
setting up a change order process
Explanation:
#carryonml
Answer:
using communication tools
Explanation:
The correct answer is using communication tools. Communication tools such as online surveys help project teams identify customers’ wants and needs.
An add tape of 101 ft is incorrectly recorded as 100 ft for a 200-ft distance. What is
the correct distance?
Answer:
the correct distance is 202 ft
Explanation:
The computation of the correct distance is shown below:
But before that correction to be applied should be determined
= (101 ft - 100 ft) ÷ (100 ft) × 200 ft
= 2 ft
Now the correct distance is
= 200 ft + 2 ft
= 202 ft
Hence, the correct distance is 202 ft
The same would be relevant and considered too
Q-) please give me a reference about Tack coat? Pleae i need it please??!!
Answer:
Tack coat is a sprayed application of an asphalt binder upon an existing asphalt or Portland cement concrete pavement prior to an overlay, or between layers of new asphalt concrete.
Explanation:
Assume, X Company Limited (XCL) is one of the leading 4th generation Life Insurance
Companies in Bangladesh. The Company is fully customer focused. This Life insurance company are
experimenting with analysis of consumer profiles (to determine whether a person eats healthy food,
exercises, smokes or drinks too much, has high-risk hobbies, and so on) to estimate life expectancy.
Companies might use the analysis to find populations to market policies to. From the perspective of
privacy, what are some of the key ethical or social issues raised? Evaluate some of them.
Answer:
The issues related to the privacy are:
1. Informational privacy
2. Discrimination factors
3. Biased grouping on the basis of Data mining
4. Lack of consent
5. Morally wrong
6. Illegal distribution of information risks
7. Possibility of threat to life
Let's look at some major concerns:
1. Informational privacy : The concept of privacy of the personal information is totally nullified when the information is being used for a purpose other than the intended one for which it was given. This unethical use of information even for general purposes is not correct and is a matter of concern. It is more like using the sensitive data of others for personal benefit which is purely objectionable and raises security issues. Sometimes the data is also shared with the potential employers which might have certain impacts we are unaware of.
2. Data mining issues : The process of using a certain information to arrive and understand the trend and outcomes is called data mining. In this case, the consumer's data undergoes grouping and might get placed in the wrong group rather than the actual one. Also, there can be a case of biasing towards the groups which are not be focused on, or are not a part of the intended audience. This leads to the discrimination factors if we see it from a social point of view.
3. Lack of consent : Use of information without the consent or awareness of the consumers raises concern over the business ethics followed by the company. No one deserves the right to misuse information for his personal benefits without any of its information to the consumer. It is morally wrong and againt the work ethics. Moreover, it raises trust issues between the two involved, and hence is socially unacceptable.Explanation:
Which option identifies the specialized field of engineering that would best suit Erik in the following scenario?
Erik is an accounting major, but he fears that working with numbers all day may be a bit constrictive for him. His roommate is an engineering
major and is planning to specialize in chemical engineering, Erik is not interested in chemistry, but he does find engineering fascinating.
O structural engineering
O materials engineering
industrial engineering
O aerospace engineering
Answer:
industrial engineering
Explanation:
three ways to advertise for AVID
Answer:
newspaper, radio, televison
Explanation:
had avid in 7th :)
Answer:
1. will help for colcollares.
2. gives you money for studies
3. helps you choose the perfect collage
4.54 Saturated liquid nitrogen at 600 kPa enters a boiler at a rate of 0.008 kg/s and exits as saturated vapor (see Fig. P4.54). It then flows into a superheater also at 600 kPa, where it exits at 600 kPa, 280 K. Find the rate of heat transfer in the boiler and the superheater.
Answer:
hello the figure attached to your question is missing attached below is the missing diagram
answer :
i) 1.347 kW
ii) 1.6192 kW
Explanation:
Attached below is the detailed solution to the problem above
First step : Calculate for Enthalpy
h1 - hf = -3909.9 kJ/kg ( For saturated liquid nitrogen at 600 kPa )
h2- hg = -222.5 kJ/kg ( For saturated vapor nitrogen at 600 kPa )
second step : Calculate the rate of heat transfer in boiler
Q1-2 = m( h2 - h1 ) = 0.008( -222.5 -(-390.9) = 1.347 kW
step 3 : find the enthalpy of superheated Nitrogen at 600 Kpa and 280 K
from the super heated Nitrogen table
h3 = -20.1 kJ/kg
step 4 : calculate the rate of heat transfer in the super heater
Q2-3 = m ( h3 - h2 )
= 0.008 ( -20.1 -(-222.5 ) = 1.6192 kW
a tensile specimen with a 12mm initial diameter and 50mm gage length reaches maximum load at 90KN and fractures at 70KN
the minimum diameter at fracture is 10mm
determine the engineering stress at maximum load and the true fracture stress.
Answer:
i) 796.18 N/mm^2
ii) 1111.11 N/mm^2
Explanation:
Initial diameter ( D ) = 12 mm
Gage Length = 50 mm
maximum load ( P ) = 90 KN
Fractures at = 70 KN
minimum diameter at fracture = 10mm
Calculate the engineering stress at Maximum load and the True fracture stress
i) Engineering stress at maximum load = P/ A
= P / [tex]\pi \frac{D^2}{4}[/tex] = 90 * 10^3 / ( 3.14 * 12^2 ) / 4
= 90,000 / 113.04 = 796.18 N/mm^2
ii) True Fracture stress = P/A
= 90 * 10^3 / ( 3.24 * 10^2) / 4
= 90000 / 81 = 1111.11 N/mm^2
A cylindrical metal specimen having an original diameter of 10.33 mm and gauge length of 52.8 mm is pulled in tension until fracture occurs. The diameter at the point of fracture is 6.38 mm, and the fractured gauge length is 73.9 mm. Calculate the ductility in terms of (a) percent reduction in area (percent RA), and (b) percent elongation (percent EL).
Answer
a) 62 percent
b) 40 percent
Explanation:
Original diameter ( d[tex]_{i}[/tex] ) = 10.33 mm
Original Gauge length ( L[tex]_{i}[/tex] ) = 52.8 mm
diameter at point of fracture ( d[tex]_{f}[/tex] ) = 6.38 mm
New gauge length ( L[tex]_{f}[/tex] ) = 73.9 mm
Calculate ductility in terms of
a) percent reduction in area
percentage reduction = [ (A[tex]_{i}[/tex] - A[tex]_{f}[/tex] ) / A[tex]_{i}[/tex] ] * 100
A[tex]_{i}[/tex] ( initial area ) = π /4 di^2
= π /4 * ( 10.33 )^2 = 83.81 mm^2
A[tex]_{f}[/tex] ( final area ) = π /4 df^2
= π /4 ( 6.38)^2 = 31.97 mm^2
hence : %reduction = ( 83.81 - 31.97 ) / 83.81
= 0.62 = 62 percent
b ) percent elongation
percentage elongation = ( L[tex]_{f}[/tex] - L[tex]_{i}[/tex] ) / L[tex]_{i}[/tex]
= ( 73.9 - 52.8 ) / 52.8 = 0.40 = 40 percent
A cylindrical bar of metal having a diameter of 19.9 mm and a length of 186 mm is deformed elastically in tension with a force of 42600 N. Given that the elastic modulus and Poisson's ratio of the metal are 67.1 GPa and 0.34, respectively, determine the following: (a) The amount by which this specimen will elongate (in mm) in the direction of the applied stress. (b) The change in diameter of the specimen (in mm). Indicate an increase in diameter with a positive number and a decrease with a negative number.
Answer:
a) 0.347 mm
b) - 0.0126 mm
Explanation:
Diameter of metal bar = 19.9 mm
length = 186 mm = 0.186 m
Tension force = 42600 N
elastic modulus = 67.1 GPa
Poisson's ratio = 0.34
a) calculate the amount by which the specimen will elongate
first calculate the area of metal bar
Area = πd^2 / 4 = π/4 ( 19.9 )^2 = 3.11 * 10^-4 m^2
Elongation ( E ) = б / e = P/A * L / ΔL
and ΔL = PL / AE
hence the elongation ( ΔL) = [ (42600 * 0.186 ) / ( 3.4*10^-4 * 67.1 * 10^9 ) ]
= 3.47 * 10^-4 m ≈ 0.347 mm
b) Calculate the change in diameter of specimen
μ = -( Δd / d) / ( ΔL/L )
0.34 = - (Δd / 19.9 ) / ( 0.347 / 186 )
∴ Δd = 0.34 * 0.00186 * 19.9 = - 0.0126 mm
consider a stead flow ideal carnot cycle using steam as the working fluid in which the high temperature constant pressure heat addition process starts with a saturated liquid and ends with a saturated vapor. plot this cycle in t-s coordinates showing the steam dome. calculate the thermal efficiency for this cycle if the pressure of the high temperature steam is 6 mpa and the low temperature heat rejection process occurs at 300 k.
Answer:
45.32%
Explanation:
Given data:
pressure of high temperature steam = 6 MPa
low temperature heat rejection process ( Tr ) = 300 k
A) plot of cycle in t-s coordinates showing steam dome
attached below
B) Calculate thermal efficiency
thermal efficiency = 1 - (Tr / Tsat )
Tsat = 275.59°C ≈ 548.59 K ( from steam table at Pa = 6 MPa )
back to equation 1
1 - (300 / 548.59 )
1 - 0.5468 = 0.4532 = 45.32%
The volume of a right circular cone of radius r and height h is V = 1 3 πr 2h (a) (i) Find a formula for the instantaneous rate of change of V with respect to r if r changes and h remain constant. (ii) Suppose that h = 2 is fixed but r varies. Find the rate of change of V w. R. To r at the point where r = 4.
Answer:
(i) [tex]\frac{2}{3}[/tex][tex]\pi[/tex]rh
(ii) [tex]\frac{16}{3}[/tex][tex]\pi[/tex]
Explanation:
Given:
V = [tex]\frac{1}{3}[/tex][tex]\pi[/tex]r²h
Where;
V = volume of a right circular cone.
r = radius of the cone
h = height of the cone.
(i) The rate of change of V with respect to r if r changes and h remains constant is [tex]\frac{dV}{dr}[/tex], and is given by finding the differentiation of V with respect to r as follow:
[tex]\frac{dV}{dr}[/tex] = [tex]\frac{d}{dr}[/tex][[tex]\frac{1}{3}[/tex][tex]\pi[/tex]r²h]
[tex]\frac{dV}{dr}[/tex] = [tex]\frac{2}{3}[/tex][tex]\pi[/tex]rh --------------------(i)
(ii)
Given;
h = 2
r = 4
Substitute these values into equation (i) as follows;
[tex]\frac{dV}{dr}[/tex] = [tex]\frac{2}{3}[/tex][tex]\pi[/tex](4 x 2)
[tex]\frac{dV}{dr}[/tex] = [tex]\frac{2}{3}[/tex][tex]\pi[/tex](8)
[tex]\frac{dV}{dr}[/tex] = [tex]\frac{16}{3}[/tex][tex]\pi[/tex]
[tex]\frac{dV}{dr}[/tex] = [tex]\frac{16}{3}[/tex][tex]\pi[/tex]
A right circular cone is one where the axis of cones is the line connecting the vertex to circular base's midway, the volume of right circular cone as follows:
Volume calculation:Formula:
[tex]V = \frac{1}{3} \pi r^2h[/tex]
Where;
V = right circular cone volume
r = Cone radius.
h = Cone height.
The calculation for part 1:
[tex]\frac{dV}{dr}[/tex] is indeed the rate of change of V with reference to r when r changes but h remains constant, and it is calculated via calculating the differentiation of V with respect to r as follows:
[tex]\to \frac{dV}{dr} =\frac{d}{d}r [ \frac{1}{3} \pi r^2h] =\frac{2}{3} \pi r h[/tex]
The calculation for part 2:
When h = 2 and r = 4 then substituting the value into the part 1 equation then:
[tex]\to \frac{dV}{dr} = \frac{2}{3} \pi (4 \times 2) = \frac{2}{3} \pi (8) = \frac{16}{3} \pi[/tex]
Find out more about the volume here:
brainly.com/question/24086520
pacing pieces of information into groups to remember them better is called
a.
Visualizing
c.
Rhyming
b.
Keywording
d.
Categorizing
Please select the best answer from the choices provided
Answer:
D. Categorizing
Explanation:
pls mark me as your brainlist
Answer:
D
Explanation:
Tungsten is being used at half its melting point (Tm≈3,400◦C) and astress level of 160 MPa. An engineer suggests increasing the grain size by afactor of 4 as an effective means of reducing the creep rate.(a)Do you agree with the engineer? Why? What if the stress level were equalto 1.6 MPa?(b)What is the predicted increase in length of the specimen after 10,000hours if the initial length is 10 cm?
Answer:
Explanation:
The missing diagram is attached in the image below which shows the deformation map of the Tungsten.
Given that:
Stress level [tex]\sigma = 160 MPa[/tex]
T = 0.5 Tm
[tex]\implies \dfrac{T}{Tm} = 0.5[/tex]
G = 160 GPa
[tex]\implies \dfrac{\sigma}{G} = 10^{-3}[/tex]
a)
The regulating creep mechanism is dislocation driven, as we can see from the deformation mechanism.
The engineer's recommendation would not be approved because increasing grain size results in a decrease in the grain-boundary count, preferring dislocation motion. The existence of grain borders is a hindrance to dislocation motion, as the dislocation principle explicitly states. To stop the motion, we'll need a substance with finer grains, which would result in more grain borders, or a material with higher pressure. In the case of Nabarro creep, which is diffusion-driven, an engineer's recommendation would be useful.
b)
If stress level reduced to [tex]\sigma = 1.6 MPa[/tex]
[tex]\implies \dfrac{\sigma }{G} = 10^{-5}[/tex]
Cable creep is now the controlling creep mode, which entails tension-driven atom diffusion along grain borders to elongate grain along the stress axis, a process known as grain-boundary diffusion. Cable creep is more common in fine-grained materials. As a result, the engineer's advice would succeed in this case. The affinity for cable creep is reduced when the grain size is increased.
c)
From the map of creep mechanism for [tex]\dfrac{\sigma}{G} = 10^{-3} \ and \ \dfrac{T}{Tm} = 0.5[/tex]
We read strain rate [tex](e) = 10^{-6}/sec[/tex]
Therefore,
[tex]Strain (E) = e * \Delta t[/tex]
[tex]= 10^{-6} \times 10000 \times 3600[/tex]
= 36
Therefore, [tex]\Delta L = E \times Li[/tex]
= [tex]36 * 10 cm[/tex]
= 360 cm
Thus, the increase in length = 360 cm
Consider a mild steel specimen with yield strength of 43.5 ksi and Young's modulus of 29,000 ksi. It is stretched up to a point where the strain in the specimen is 0.2% (or 0.002). If the specimen is unloaded (i.e. load reduces to zero), the residual strain (or permanent set) is: 0.05% 0.1% 0% 0.2%
Answer:
0.05%
Explanation:
From the question, we have;
The yield strength of the mild steel, [tex]\sigma _c[/tex] = 43.5 ksi
Young's modulus of elasticity, ∈ = 29,000 ksi
The total strain, [tex]\epsilon _c[/tex] = 0.2% = 0.002
The inelatic strain [tex]\epsilon_c^{in}[/tex] is given as follows;
[tex]\epsilon_c^{in}[/tex] = [tex]\epsilon _c[/tex] - [tex]\sigma _c[/tex]/∈
Therefore, we have;
[tex]\epsilon_c^{in}[/tex] = 0.002 - 43.5/(29,000) = 0.0005
Therefore, the inelastic strain, [tex]\epsilon_c^{in}[/tex] = 0.0005 = 0.05%
Taking the inelastic strain as the residual strain, we have;
The residual strain = 0.05%
Which of the following identifies three advantages of PLM software?
reduced cost, faster marketing, and process transparency
faster marketing, process transparency, and outsourcing
process transparency, outsourcing, and reduced cost
outsourcing, reduced cost, and faster marketing
Answer:
reduced cost, faster marketing, and process transparency
Explanation:
The correct answer is reduced cost, faster marketing, and process transparency. PLM software helps coordinate tasks during implementation.
what is the answer to life the universe and everything
(worth 95 points!)
Answer:
In the absence of dark energy, a flat universe expands forever but at a continually decelerating rate, with expansion asymptotically approaching zero; with dark energy, the expansion rate of the universe initially slows down, due to the effects of gravity, but eventually increases, and the ultimate fate of the universe ...
Explanation:
I think it goes on forever.
Help meeeeeeeee plzzzzz need explanation
the picture is blank for me what does it say i can comment the answer plz mark brainlyist