Answer:
A bread board
Explanation:
It has identical holes where every component is connected using jumper wires
[tex]{}[/tex]
a must be correctly applied so that it is strong enough to hold the assembly and still not interfere with the finished welding.
A tack weld must be correctly applied so that it is strong enough to hold the assembly and still not interfere with the finished welding.
Who is wielding?A wielder can be defined as an individual who is saddled with responsibility of joining two or more metals together by wielding, especially through the use of an electrode or gas wielding method.
During the process of wielding, sparks and minute metallic objects are produced, which are usually hazardous to both the wielder and other workers within the vicinity.
In Mechanical Engineering, a tack weld should be correctly applied to the metals that are being wielded, so that they are strong enough to hold the assembly without interfering with the finished welding.
Read more on welding here: https://brainly.com/question/21049525
#SPJ1
Complete Question:
A ____ must be correctly applied so that it is strong enough to hold the assembly and still not interfere with the finished welding.
a-forged weld
b-stick weld
c-tack weld
d-rod weld
what is 4+12 if 4=4 and 12=12?
Answer:
16
Explanation:
thermal-hydraulic study of the lbe-cooled fuel assembly in the myrrha reactor: experiments and simulations
For many cutting-edge systems based on fast neutrons, heavy liquid metals (HLMs), such as lead-bismuth eutectic (LBE) and pure lead, are popular candidate coolants.
LBE is employed, in instance, in Mol (Belgiumgroundbreaking )'s MYRRHA fast reactor, which can run in either critical mode or as a sub-critical accelerator-driven system. Key thermal-hydraulic features of these systems, such as the proper cooling of fuel components, must be evaluated with a heavy emphasis on safety.
This flow scenario presents a challenge for computational fluid dynamics (CFD) models, such as those used to relate the turbulent transport of momentum and heat, due to the complicated geometry and low Prandtl number of the LBE (Pr 0.025). Therefore, accurate experimental information is required for validation.
Learn more about bismuth:
https://brainly.com/question/7622627
#SPJ4
The complete questions is ''what is the thermal-hydraulic study of the lbe-cooled fuel assembly in the myrrha reactor: experiments and simulations''.
technician a says that gasoline engines have spark plugs to ignite the air-fuel mixture.technician b says that diesel engines use compression to ignite the air-fuel mixture. who iscorrect?
It is right to state that Technician B is correct. A piston compresses the air in the cylinder, causing it to become very hot. The diesel is then atomized in the injectors and sprayed into the heated air as a mist. The heated air ignites the gasoline quickly, creating ignition.
What is compression in Engines?As the fuel injectors drive air and fuel into the combustion chamber, compression occurs in the internal combustion cylinders.
The mixture ignites, and the piston is driven by the expansion of the burning gases in the cylinders, converting the energy from combustion into mechanical energy that propels the vehicle.
Learn more about Piston Compression:
https://brainly.com/question/10072505
#SPJ1
Identifying majors with specific language and mathematics requirements using the degree search selection filters help you solve what type of business problem?.
Structured business problem is being identified here. An organizational structure serves to facilitate the achievement of goals and objectives by the organization as well as the effective and efficient completion of tasks by personnel.
An organizational structure is a type of framework that specifies how certain tasks are to be find out in order to achieve the objectives of an organization. Obligations, rules, and roles may be a part of these activities. information is transferred across layers of the organization is likewise supervised by its organizational structure. The sole control, partnership, corporation, and S corporation are the four most popular business structures. workers will profit from structure because it'll give clarity, manage prospects, refine decision- timber, and ensure thickness. Organizational charts also delegate responsibility, streamline workflow, and guarantee the timely completion of crucial activities.
Learn more about structure here-
https://brainly.com/question/10730450
#SPJ4
Describe the standard algorithm for finding the binary representation of a positive decimal integer
in English.
in pseudocode
Answer:
the perimeter of a square room is 48m. what is the area of the room? What cost will incur if the rate of carpeting the room is Rs. 10 per m square
What error results if the curvature and refraction correction is neglected in trigonometric leveling for sights: (a) 3000 ft long (b) 1200 m long (c) 4500 ft long?
The error results if the curvature and refraction correction is neglected in trigonometric levelling for sights are
(a) 3000 ft long. = 0.1854 ft
(b) 1200 m long = 0.0972 m
(c) 4500 ft long = 0.4172 ft
What is levelling?This refers to the term in surveying used to describe taking measurements of heights with reference to a datum. Levelling is achieved using levelling instruments.
How to find the error results if the curvature and refraction correction is neglectedgiven data
(a) 3000 ft long
(b) 1200 m long
(c) 4500 ft long
(a) 3000 ft long
= 0.0206 * F^2
= 0.0206 * ( 3000 / 1000 )^2
= 0.0206 * ( 3 )^2
= 0.0206 * ( 9 )
= 0.1854 ft
(b) 1200 m long
= 0.0675 * K^2
= 0.0675 * ( 1200 / 1000 )^2
= 0.0675 * ( 1.2 )^2
= 0.0675 * ( 1.44 )
= 0.0972 m
(c) 4500 ft long
= 0.0206 * F^2
= 0.0206 * ( 4500 / 1000 )^2
= 0.0206 * ( 4.5 )^2
= 0.0206 * ( 20.25 )
= 0.4172 ft
Read more on corrections for curvature and refraction here: https://brainly.com/question/20820908
#SPJ1
Who Can Help my assignment?
Answer:
me
Explanation:
Which of the following is not a characteristic of an external combustion engine?
A. External pistons are used.
B. Fuel is sent directly to the engine.
C. Boiler burns fuel to produce steam.
D. Steam is sent to the engine to produce power.
A dashed line with an “S” designates a(n) ____
Hi there,
I hope you and your family are staying safe and healthy!
A dashed line with an S designates an Underfloor signal raceway.
All the best this semester!
~Garebear
(5 points) Some strands of Christmas tree lights are sometimes wired in series. What happens to the other lights if one of the series bulbs is removed? Other lights are sometimes wired in parallel. What happens when one of these parallel bulbs is removed? Explain why
Answer:
Series: All the lights go out
Parallel: Nothing happens
Explanation:
Often referred to as ‘daisy-chained’ or ‘looped’ the current in a series circuit follows one path from start-to-finish with the Anode (positive) of the second LED connected to the Cathode (negative) of the first. The image to the right shows an example: To wire a series circuit like the one shown, the positive output from the driver connects to the positive of the first LED and from that LED a connection is made from the negative to the positive of the second LED and so on, until the last LED in the circuit. Finally, the last LED connection goes from the negative of the LED to the negative output of the constant current driver, creating a continuous loop or daisy chain. When one goes out, the whole strand of light stops working with it.
Parallel circuit (when lights are wired in parallel):
Where a series circuit receives the same current to each LED, a parallel circuit receives the same voltage to each LED and the total current to each LED is the total current output of the driver divided by the number of parallel LEDs.
In a parallel circuit all the positive connections are tied together and back to the positive output of the LED driver and all the negative connections are tied together and back to the negative output of the driver. Lets take a look at this in the image to the right. Using the example shown with a 1000mA output driver, each LED would receive 333mA; the total output of the driver (1000mA) divided by the number of parallel strings (3).
How do I test the functionality of a semiconductor diode using a DMM
Answer:
• Dismount the diode from the circuit board (PCB or veroboard)
• Switch on the DMM and connect its positive (red) probe to anode terminal of a diode as well as a negative (black) probe to the cathode terminal.
• The DMM must be in parameters of continuity.
• If a beep sound is heard, the diode is functioning.
[tex]{}[/tex]
A box barge 65 m long and 12 m wide floats at a draught of 5.5 m in sea water. calculate: a) the displacement of the barge, b) its draught in fresh water.
The Displacement of the Barge whose length 65m and 12m wide- 4375.8 tonnes(a) and the Draught in Fresh Water- 5.61 m(b).
Let density of sea-water be- 1020kg/m3
Displacement of the barge= Density of sea water* Volume Displaced
=1020* (12*65*5.5)
=4375800 kg
=4375.8 tonnes
Let Density of Fresh Water- 1000kg/m3
Draught in Fresh Water= Density of sea water/Density of water *draught in sea water
1020/1000 *5.5
Draught in Fresh Water= 5.61 m
Learn more about Archimedes' Principle here:
https://brainly.com/question/787619
#SPJ4
PHOTOGRAPHY-Sarah is developing a black-and-white photograph. At what ratio should she mix the fixer solution? OA. 1:4 О в. 1-2 OD. 1:10
Since Sarah is developing a black-and-white photograph. The ratio that she should mix the fixer solution is option B. 1-2.
Which aspect ratio ought to be applied?The kind of project you're shooting will determine the appropriate aspect ratio to utilize. As a starting point, we advise utilizing 16:9 for films as well as 4:3 for images.
There is no way to go wrong with either of them because this is a good common standard.
One do advise that a person can experiment with various aspect ratios as you acquire experience and wish to try more artistic photos. This can give your content a completely new perspective.
Therefore, Since Sarah is developing a black-and-white photograph. The ratio that she should mix the fixer solution is option B. 1-2.
Learn more about photograph from
https://brainly.com/question/11324677
#SPJ1
When welding a T-joint, why should the arc be directed more toward the bottom workpiece?
When welding a T-joint, the reason that the arc need to be directed more toward the bottom workpiece is so that a person can hinder or stop any form of undercutting of the given top piece.
What is the ideal welding position for any joint?The Positioned flat of the flat position weld, often known as a "downhand" position, is the simplest and frequently the first weld that new pupils learn.
The welder places the metals to be welded flat and moves the electric arc across them while it travels across the workpiece in a way that is said to be an horizontal orientation.
Therefore, based on the above, When welding a T-joint, the reason that the arc need to be directed more toward the bottom workpiece is so that a person can hinder or stop any form of undercutting of the given top piece.
Learn more about welding from
https://brainly.com/question/9450571
#SPJ1