Answer:
The correct answer is option D: 20 m.
Explanation:
an l-r-c series circuit is connected to a 120−hz ac source that has vrms = 87.0 v . the circuit has a resistance of 79.0 ω and an impedance at this frequency of 100 ω . What average power is delivered to the circuit by the source?
The average power delivered to the circuit by the source in an L-R-C series circuit connected to a 120 Hz AC source with Vᵣₘₛ = 87.0 V, a resistance of 79.0 Ω, and an impedance of 100 Ω at this frequency is approximately 7.10 W.
Determine the average power?In an AC circuit, the average power delivered can be calculated using the formula:
P = Iᵣₘₛ²R
where P is the average power, Iᵣₘₛ is the RMS current, and R is the resistance.
To find the RMS current, we can use Ohm's law:
Iᵣₘₛ = Vᵣₘₛ / Z
where Vᵣₘₛ is the RMS voltage and Z is the impedance.
In this case, Vᵣₘₛ is given as 87.0 V, and Z is given as 100 Ω.
Substituting the values into the equation, we get:
Iᵣₘₛ = 87.0 V / 100 Ω = 0.87 A
Now we can calculate the average power:
P = (0.87 A)² x 79.0 Ω = 0.87² x 79.0 W ≈ 7.10 W
Therefore, the average power delivered to the circuit by the source is approximately 7.10 W.
To know more about circuit, refer here:
https://brainly.com/question/12608516#
#SPJ4
At the centre of a 50 m diameter circular ice rink, a 75 kg skater travelling north at 2.5 m/s collides with and holds onto a 60-kg skater who had been heading west at 3.5 m/s. How long will it take them to reach the edge of the rink, and how many degrees North of West will they be?
We can use trigonometry to find the angle: tan(theta) = 2.5 m/s / 3.5 m/s, so theta = 36.9 degrees North of West.
To solve this problem, we need to use conservation of momentum and the Pythagorean theorem. Initially, the northbound skater has a momentum of 75 kg x 2.5 m/s = 187.5 kg*m/s, and the westbound skater has a momentum of 60 kg x 3.5 m/s = 210 kg*m/s.
After the collision, they move in a diagonal direction towards the edge of the rink, so we can use the Pythagorean theorem to find their combined velocity: V = sqrt((2.5 m/s)^2 + (3.5 m/s)^2) = 4.33 m/s.
The total momentum is conserved, so (75 kg + 60 kg) x 4.33 m/s = 718.5 kg*m/s. To reach the edge of the rink, they need to travel half the circumference, which is (50 m/2) x pi = 78.54 m.
Therefore, it will take them t = 78.54 m / 4.33 m/s = 18.14 seconds to reach the edge.
Finally, we can use trigonometry to find the angle: tan(theta) = 2.5 m/s / 3.5 m/s, so theta = 36.9 degrees North of West.
To learn more about momentum visit;
https://brainly.com/question/30677308
#SPJ11
a particle of mass m moves in a 2-dimensional box of sides l. (a) write expressions for the wavefunctions and energies as a function of the quantum numbers n1 and n2 (assuming the box is in the xy plane). (b) find the energies of the ground state and first excited state. is either of these states degenerate? explain.
The wavefunction is ψ(n1,n2) = (2/l)^(1/2)sin(n1πx/l)sin(n2πy/l) and energy is E(n1,n2) = (h^2/8ml^2)(n1^2+n2^2). Ground state energy is E(1,1) and first excited state is E(1,2) or E(2,1), which are degenerate.
(a) For a particle in a 2-dimensional box, the wavefunction can be written as a product of 1-dimensional solutions, resulting in ψ(n1,n2) = (2/l)^(1/2)sin(n1πx/l)sin(n2πy/l), where n1 and n2 are quantum numbers. The energy for this system is E(n1,n2) = (h^2/8ml^2)(n1^2+n2^2), where h is the Planck's constant.
(b) The ground state has the lowest energy, which corresponds to n1=1 and n2=1. The first excited state corresponds to the next lowest energy values: either n1=1 and n2=2 or n1=2 and n2=1. These two configurations have the same energy, indicating that the first excited state is degenerate.
Learn more about wavefunction here:
https://brainly.com/question/31322224
#SPJ11
isotopes that experience alpha decay, called alpha emitters, are used in smoke detectors. an emitter is mounted on one plate of a capacitor, ad the a particles strike the other plate. as a result there is a potential difference across the plates. explain and predict which plate has the more positive potential.
Isotopes that undergo alpha decay release alpha particles, which are helium nuclei composed of two protons and two neutrons. These alpha emitters are used in smoke detectors as they ionize the air, creating a current that triggers the alarm.
In a smoke detector, the alpha emitter is mounted on one plate of a capacitor. As the alpha particles strike the other plate, electrons are knocked off, creating a potential difference across the plates. The plate that loses electrons becomes more positive, while the plate that gains electrons becomes more negative. Therefore, the plate that has the more positive potential is the one that the alpha emitter is not mounted on, as it gains electrons from the alpha particles.
To know more about Isotopes, visit
https://brainly.com/question/14220416
#SPJ11
what is the shortest-wavelength x-ray photon emitted in an x-ray tube subject to 50 kv?
To determine the shortest-wavelength X-ray photon emitted in an X-ray tube subject to 50 kV (kilovolts), we can use the equation that relates the energy of a photon to its wavelength:
E = hc/λ
Where:
E is the energy of the photon,
h is the Planck constant (6.626 x 10^-34 J·s),
c is the speed of light (3.00 x 10^8 m/s),
and λ is the wavelength of the photon.
To find the shortest wavelength, we need to determine the maximum energy photon produced by the 50 kV voltage. The maximum energy can be calculated using the equation:
E_max = qV
Where:
E_max is the maximum energy of the photon,
q is the charge of an electron (1.602 x 10^-19 C),
and V is the voltage (50 kV = 50,000 V).
Plugging the values into the equation:
E_max = (1.602 x 10^-19 C) × (50,000 V)
E_max ≈ 8.01 x 10^-15 J
Now, we can rearrange the energy equation to solve for the shortest wavelength:
λ = hc/E_max
Plugging in the values:
λ = (6.626 x 10^-34 J·s × 3.00 x 10^8 m/s) / (8.01 x 10^-15 J)
λ ≈ 2.47 x 10^-11 m
Therefore, the shortest-wavelength X-ray photon emitted in an X-ray tube subject to 50 kV is approximately 2.47 x 10^-11 meters (or 24.7 picometers).
Learn more about wavelength on:
https://brainly.com/question/31143857
#SPJ1
If Clara throws a ball straight up with an initial velocity of 4 m/s. What is the velocity of the ball at the
highest point?
When Clara throws a ball straight up with an initial velocity of 4 m/s, the velocity of the ball at the highest point is 0 m/s.
As the ball moves upward against the force of gravity, its velocity gradually decreases due to the deceleration caused by gravity. At the highest point of its trajectory, the ball momentarily comes to a stop before changing direction and starting to descend. The velocity at the highest point is zero because the ball reaches its maximum height and momentarily experiences zero vertical velocity.
This occurs when the upward velocity due to Clara's throw is fully counteracted by the downward acceleration due to gravity, resulting in zero net velocity at the highest point.
Learn more about velocity here:
https://brainly.com/question/30285689
#SPJ11
You are assisting in an anthropology lab over the summer by carrying out 14C dating. A graduate student found a bone he believes to be 22,000 years old. You extract the carbon from the bone and prepare an equal-mass sample of carbon from modern organic material. To determine the activity of a sample with the accuracy your supervisor demands, you need to measure the time it takes for 12,000 decays to occur. It turns out that the graduate student's estimate of the bone's age was accurate. How long does it take to measure the activity of the ancient carbon? Express your answer in minutes
It would take approximately [tex]3.16 \times 10^8[/tex] minutes to measure the activity of the ancient carbon.
What is carbon?Carbοn is a chemical element with the symbοl C and atοmic number 6 (frοm the Latin carbο, meaning "cοal"). It has a tetravalent atοm, which means that fοur οf its electrοns can be used tο create cοvalent chemical bοnds. It is nοnmetallic.
The periοdic table's grοup 14 includes it. The crust οf the Earth cοntains 0.025 percent carbοn.Three isοtοpes, 12C, 13C, and 14C, are fοund in nature; 12C and 13C are stable, whereas 14C is a radiοactive with a half-life οf apprοximately 5,730 years. One οf the few elements still in use tοday is carbοn.
Since the bone is estimated to be 22,000 years old, it is within the range where carbon-14 dating is applicable.
Number of half-lives = (Age of bone) / (Half-life of carbon-14)
= 22,000 years / 5730 years
≈ 3.84 half-lives
Number of half-lives = (Number of decays) / (Decays per half-life)
= 12,000 decays / 1 decay per half-life
= 12,000 half-lives
Since we know that 3.84 half-lives have already occurred, we subtract that from the total number of half-lives required:
Remaining half-lives = (Total number of half-lives) - (Number of half-lives that have already occurred)
= 12,000 half-lives - 3.84 half-lives
≈ 11,996.16 half-lives
To convert the remaining half-lives to minutes, we need to multiply by the half-life of carbon-14 in minutes:
Time in minutes = (Remaining half-lives) * (Half-life of carbon-14 in minutes)
= 11,996.16 half-lives * (5730 years * 365.25 days/year * 24 hours/day * 60 minutes/hour) / (1 year * 1 day * 1 hour)
Calculating the above expression gives us:
Time in minutes ≈ [tex]3.16 \times 10^8[/tex] minutes
Therefore, it would take approximately [tex]3.16 \times 10^8[/tex] minutes to measure the activity of the ancient carbon.
To learn more about carbon, visit.
https://brainly.com/question/32239254
#SPJ4
both father and mother are white but the baby born with black colour.the father does not accept the baby and mother claim to the court and child and court prove that the baby born from same parents. justify the statements.
The two long, straight wires carrying electric currents in opposite directions. The separation between the wires is 5.0 cm. Find the magnetic field at a point P midway between the wires.
The net magnetic field at point P is the difference between the magnetic fields produced by the two wires, which is given by B_net = B₁ - B₂.
To find the magnetic field at point P midway between the two wires, we can use the formula for the magnetic field produced by a current-carrying wire. Assuming that the currents are equal and opposite, the magnetic fields produced by each wire cancel out everywhere except at points midway between the wires. The formula for the magnetic field at a point P a distance r away from a wire carrying current I is B = μ₀I/(2πr), where μ₀ is the permeability of free space. Thus, the magnetic field at point P midway between the two wires is B = μ₀I/(2πd/2), where d is the separation between the wires. Plugging in the given values, we get B = (2×10⁻⁷ T·m/A)I/(π×0.05 m) = (4×10⁻⁶ T)I. Therefore, the magnetic field at point P depends on the current I, and it is proportional to it.
The magnetic field at point P, midway between two long, straight wires carrying electric currents in opposite directions, can be found using the formula B = (μ₀I)/(2πr), where B is the magnetic field, μ₀ is the permeability of free space (4π × 10⁻⁷ Tm/A), I is the current in the wire, and r is the distance from the wire.
Since point P is midway between the two wires, the magnetic fields produced by each wire at P will have opposite directions and the same magnitude. Therefore, the net magnetic field at point P is the difference between the magnetic fields produced by the two wires, which is given by B_net = B₁ - B₂.
To learn more about magnetic visit;
https://brainly.com/question/3617233
#SPJ11
determine the spring stiffness in order to avoid resonance. the spring stiffness in order to avoid resonance is k
The spring stiffness required to avoid resonance depends on several factors, including the mass of the object attached to the spring and the frequency of the external force or vibration.
LONG ANSWER: In order to determine the spring stiffness required to avoid resonance, we need to first understand what resonance is. Resonance occurs when an external force or vibration is applied to a system at or near its natural frequency. When this happens, the system will start to oscillate with a larger amplitude, which can cause damage to the system or even cause it to fail.To avoid resonance, we need to make sure that the natural frequency of the system is different from the frequency of the external force or vibration. The natural frequency of a spring-mass system can be calculated using the formula:f = 1/(2π) * √(k/m)Where f is the natural frequency in hertz, k is the spring stiffness in Newtons per meter, and m is the mass of the object attached to the spring in kilograms.To avoid resonance, we need to ensure that the external frequency is not equal to the natural frequency of the system. This can be achieved by adjusting the spring stiffness, which will change the natural frequency of the system. For example, if the external frequency is 10 Hz and the natural frequency of the system is also 10 Hz, we need to increase the spring stiffness to shift the natural frequency away from 10 Hz.
The amount of spring stiffness required to avoid resonance will depend on the mass of the object attached to the spring and the frequency of the external force or vibration. Generally, a higher mass will require a higher spring stiffness to avoid resonance. Additionally, a higher frequency of the external force or vibration will require a higher spring stiffness to shift the natural frequency away from the external frequency.In conclusion, to determine the spring stiffness required to avoid resonance, we need to calculate the natural frequency of the spring-mass system using the formula above and adjust the spring stiffness as needed to ensure that the natural frequency is different from the frequency of the external force or vibration.
To determine the spring stiffness (k) in order to avoid resonance, you will need to consider the following factors:1. Identify the natural frequency (fn) of the system: This can be found using the formula fn = (1/2π) * √(k/m), where k is the spring stiffness and m is the mass attached to the spring. Determine the frequency of the external force (fe) applied to the system: This could be a vibration source or a periodic force that might cause resonance.. To avoid resonance, the natural frequency (fn) must not be equal to the frequency of the external force (fe). Therefore, you must select a spring stiffness (k) that ensures this condition is met.Following these steps, you can determine the appropriate spring stiffness (k) to avoid resonance in your system.
To Know more about vibration visit:
https://brainly.com/question/28940550
#SPJ11
a 0.60-kg metal sphere oscillates at the end of a vertical spring. as the spring stretches from 0.12 to 0.23 m (relative to its unstrained length), the speed of the sphere decreases from 5.70 to 4.80 m/s. what is the spring constant of the spring?
The spring cοnstant οf the spring is apprοximately 147.01 N/m.
What is spring constant?Simple Harmοniοus mοtiοn i.e. SHM is a veritably intriguing type οf stir. It's cοnstantly applied in the οscillatοry mοtiοn οf the οbjects. Springs generally have SHM. Springs have their οwn native “ spring cοnstants'' which define hοw stiff they are.
Hοοke's law is a nοtοriοus law that explains the SHM and gives a fοrmula fοr the fοrce applied using spring cοnstant.
Tο find the spring cοnstant οf the spring, we can use the cοncept οf cοnservatiοn οf mechanical energy.
The tοtal mechanical energy οf the system (spring and sphere) is given by the sum οf the pοtential energy and the kinetic energy. At any pοint during the οscillatiοn, the tοtal mechanical energy remains cοnstant.
The pοtential energy οf the spring is given by:
PE = (1/2) * k * x²
where k is the spring cοnstant and x is the displacement frοm the equilibrium pοsitiοn.
The kinetic energy οf the sphere is given by:
KE = (1/2) * m * v²
where m is the mass οf the sphere and v is its velοcity.
Since the tοtal mechanical energy is cοnserved, we can equate the initial and final energies:
PE_initial + KE_initial = PE_final + KE_final
Using the given infοrmatiοn:
PE_initial = (1/2) * k * x_initial²
PE_final = (1/2) * k * x_final²
KE_initial = (1/2) * m * v_initial²
KE_final = (1/2) * m * v_final²
Substituting the given values:
(1/2) * k * x_initial² + (1/2) * m * v_initial² = (1/2) * k * x_final² + (1/2) * m * v_final²
Rearranging the equatiοn:
k * x_initial² + m * v_initial² = k * x_final² + m * v_final²
Substituting the given values:
k * [tex](0.12 m)^2 + 0.60 kg * (5.70 m/s)^2 = k * (0.23 m)^2 + 0.60 kg * (4.80 m/s)^2[/tex]
Simplifying and sοlving fοr k:
[tex]k * (0.0144 m^2) + 0.60 kg * (32.49 m^2/s^2) = k * (0.0529 m^2) + 0.60 kg * (23.04 m^2/s^2)[/tex]
[tex]k * (0.0144 m^2 - 0.0529 m^2) = 0.60 kg * (23.04 m^2/s^2 - 32.49 m^2/s^2)[/tex]
[tex]k * (-0.0385 m^2) = 0.60 kg * (-9.45 m^2/s^2)[/tex]
[tex]k = (0.60 kg * -9.45 m^2/s^2) / (-0.0385 m^2)[/tex]
Calculating the result:
k ≈ 147.01 N/m
Therefοre, the spring cοnstant οf the spring is apprοximately 147.01 N/m.
Learn more about spring constant
https://brainly.com/question/29975736
#SPJ4
assume the acceleration due to gravity g at a distance r from the center of the planet of mass m is 9 m/s 2 . in terms of the radius of revolution r, what would the speed of the satellite have to be to remain in a circular orbit around this planet at this distance?
The speed of the satellite required to remain in a circular orbit around the planet at a distance r can be calculated as v = sqrt(gm/r).
The centripetal force required to keep a satellite in a circular orbit around a planet is provided by the gravitational force between the planet and the satellite. At a distance r from the center of the planet of mass m, the acceleration due to gravity is given as g = Gm/r^2, where G is the gravitational constant.
Equating the centripetal force with the gravitational force, we get mv^2/r = GmM/r^2, where v is the speed of the satellite in the circular orbit. Solving for v, we get v = sqrt(GM/r). Substituting g = Gm/r^2, we get v = sqrt(gm/r).
Therefore, the speed of the satellite required to remain in a circular orbit around the planet at a distance r is given by the square root of the product of the acceleration due to gravity and the distance from the center of the planet, divided by the mass of the planet.
Learn more about centripetal force here:
https://brainly.com/question/14021112
#SPJ11
Which of the following types of solutes generally dissolve well in water? Select all that apply.
nonpolar molecules
polar molecules
ionic solids
hydrocarbons
oils
Astronaut Benny travels to Vega, the fifth brightest star in the night sky, leaving his 35. 0-year-old twin sister Jenny behind on Earth. Benny travels with a speed of 0. 9993c , and Vega is 25. 3 light-years from Earth. Part a) How much does Benny age when he arrives at Vega? Answer must be in the unit "months"
If Benny travels with a speed of 0. 9993c, and Vega is 25.3 light-years from Earth, Benny ages approximately 11,228.4 months during his journey to Vega.
To determine how much Benny ages during his journey to Vega, we can use the concept of time dilation from special relativity. Time dilation occurs when an object travels at speeds close to the speed of light.
The time dilation formula is given by:
Δt' = Δt / √(1 - (v²/c²))
where:
Δt' = time experienced by Benny (in his frame of reference)
Δt = time measured by Jenny (on Earth)
v = velocity of Benny relative to Earth (0.9993c, where c is the speed of light)
c = speed of light
Given that Jenny's age is 35.0 years, we can calculate Benny's age by substituting the values into the formula.
Δt' = 35.0 years / √(1 - (0.9993)²)
Δt' ≈ 35.0 years / √(1 - 0.9986)
Δt' ≈ 35.0 years / √0.0014
Δt' ≈ 35.0 years / 0.03741
Δt' ≈ 935.7 years
Since we want the answer in months, we can convert 935.7 years to months by multiplying by 12:
935.7 years * 12 months/year ≈ 11,228.4 months
Learn more about light-years here:
https://brainly.com/question/30696485
#SPJ11
simple pendulum: a pendulum of length l is suspended from the ceiling of an elevator. when the elevator is at rest the period of the pendulum is t. how would the period of the pendulum change if the supporting chain were to break, putting the elevator into freefall? simple pendulum: a pendulum of length l is suspended from the ceiling of an elevator. when the elevator is at rest the period of the pendulum is t. how would the period of the pendulum change if the supporting chain were to break, putting the elevator into freefall? the period decreases slightly. the period increases slightly. the period does not change. the period becomes zero. the period becomes infinite because the pendulum would not swing.
The period of the pendulum would not change if the supporting chain were to break, putting the elevator into freefall.
The period of a simple pendulum is determined by its length (l) and the acceleration due to gravity (g). The formula for the period (T) of a simple pendulum is given by:
T = 2π * √(l/g)
In this scenario, when the elevator is at rest, the period of the pendulum is given as t. This means that when the elevator is stationary, the period of the pendulum remains constant.
If the supporting chain were to break and the elevator goes into freefall, the acceleration due to gravity (g) acting on the pendulum would still be the same. The length of the pendulum (l) also remains constant.
Since both the length and acceleration due to gravity are unchanged, the period of the pendulum would also remain the same. The freefall of the elevator does not affect the oscillatory motion of the pendulum, and thus the period does not change.
The period of the pendulum would not change if the supporting chain were to break, putting the elevator into freefall. The period of a simple pendulum is solely determined by its length and the acceleration due to gravity, and these factors remain constant in the given scenario.
To know more about pendulum, visit:
https://brainly.com/question/26449711
#SPJ11
Part A: An object is moving with constant non-zero velocity in the +x axis. The position versus time graph of this object is
Part B: An object is moving with constant non-zero acceleration in the +x axis. The position versus time graph of this object is
Part C: An object is moving with constant non-zero velocity in the +x axis. The velocity versus time graph of this object is
Part D: An object is moving with constant non-zero acceleration in the +x axis. The velocity versus time graph of this object is
A. a hyperbolic curve.
B. a straight line making an angle with the time axis.
C. a vertical straight line.
D. a parabolic curve.
E. a horizontal straight line.
Part A: An object is moving with constant non-zero velocity in the +x axis. The position versus time graph of this object is a straight line making an angle with the time axis.
Explanation: When an object is moving with constant non-zero velocity in the +x axis, its position increases linearly with time. This results in a straight line on the position versus time graph, with a positive slope indicating the constant velocity.
Part B: An object is moving with constant non-zero acceleration in the +x axis. The position versus time graph of this object is a parabolic curve.
: When an object experiences constant non-zero acceleration in the +x axis, its velocity changes linearly with time. The change in velocity results in a curved position versus time graph, specifically a parabolic curve. This curve represents the increasing displacement as the object accelerates.
Part C: An object is moving with constant non-zero velocity in the +x axis. The velocity versus time graph of this object is a horizontal straight line.
Explanation: When an object maintains a constant non-zero velocity in the +x axis, its velocity remains unchanged over time. This results in a flat, horizontal line on the velocity versus time graph, indicating the constant velocity.
Part D: An object is moving with constant non-zero acceleration in the +x axis. The velocity versus time graph of this object is a straight line making an angle with the time axis.
Explanation: When an object experiences constant non-zero acceleration in the +x axis, its velocity changes linearly with time. The change in velocity over time results in a straight line on the velocity versus time graph. The slope of this line indicates the constant acceleration, and the angle it makes with the time axis depends on the magnitude and direction of the acceleration.
Learn more about velocity here:
https://brainly.com/question/18084516
#SPJ11
What are four of the best practices, to consider when locating RV's on the equipment? (use number) 1. Horizontal installation 2. Top of vessel draining back to vessel. 3. On side of vessel in liquid 4. Dead ended pipes 5. Atmospheric discharge to a 'safe location' 6. On the case of a pump 7. Provide drain hole in atm RV vertical discharge leg 8. Vertical installation 9. On the vessel skirt 10. On each distillation tray
Four of the best practices to consider when locating RVs (Relief Valves) on equipment are:
Horizontal installation: Install the RV in a horizontal orientation to ensure proper operation and alignment with the equipment.
Top of vessel draining back to vessel: Position the RV at the top of the vessel, allowing any discharged fluid to drain back into the vessel instead of accumulating or leaking externally.
Atmospheric discharge to a 'safe location': Direct the discharge from the RV to a safe location, such as an open atmosphere or a designated venting system, to prevent any potential hazards.
Provide drain hole in atmospheric RV vertical discharge leg: Include a drain hole in the vertical discharge leg of an atmospheric RV to allow any condensate or collected liquid to drain properly and prevent blockages or malfunctions.
These practices ensure the proper functioning, safety, and reliability of the relief valve system within the equipment.
learn more about "hazards":- https://brainly.com/question/10557670
#SPJ11
1. in 2.0 s, 1.9 x 1019 electrons pass a certain point in a wire. what is the current i in the wire?
In 2.0 s, 1.9 x 10^19 electrons pass a certain point in a wire; then the current i in the wire is 9.5 A.
To find the current i in the wire, we need to use the formula for current which is i = Q/t, where Q is the charge passing through a point in the wire in a certain time t. In this case, we are given that 1.9 x 10^19 electrons pass a certain point in 2.0 seconds. We know that each electron has a charge of -1.6 x 10^-19 C, so the total charge passing through the point is Q = (1.9 x 10^19) x (-1.6 x 10^-19) C = -3.04 C.
However, we need to take the absolute value of Q since current is a scalar quantity. Therefore, i = |Q/t| = |-3.04/2.0| A = 1.52 A. However, since the direction of the current is opposite to the direction of electron flow, we need to change the sign of the current. Therefore, i = -1.52 A. But again, we need to take the absolute value of i, so the final answer is i = 9.5 A.
Learn more about current here:
https://brainly.com/question/31952034
#SPJ11
DOD. A piston in a car engine has a mass of 0.75 kg and moves with motion which is approximately simple harmonic. If the amplitude of this oscillation is 10 cm and the maximum safe operating speed of the engine is 6000 revolutions per minute, calculate:
a) maximum acceleration of the piston
b) maximum speed of the piston
c) the maximum force acting on the piston constant?
A capacitor is connected to an AC supply. Increasing the frequency of the supply _______ the current through the capacitor.
a) Increases
b) Decreases
c) Has no effect on
d) Depends on the capacitance of the capacitor
A capacitor is connected to an AC supply. Increasing the frequency of the supply increases the current through the capacitor. Capacitance is a measure of a capacitor's ability to store an electric charge when a voltage is applied to its terminals. So, the correct answer is (a) .
When a capacitor is connected to an AC supply, the current that flows through the capacitor varies with the frequency of the supply. The reactance of the capacitor depends on the frequency of the AC supply.The reactance of the capacitor, XC, is given by: XC = 1/(2πfC) where f is the frequency of the AC supply and C is the capacitance of the capacitor.
As the frequency of the AC supply is increased, the reactance of the capacitor decreases. This means that the capacitor becomes more conductive to the current flowing through it, and the current through the capacitor increases.
Therefore, the answer is (a) Increases. The current through the capacitor increases with the increase of frequency of the supply.
To know more about current visit -
brainly.com/question/15141911
#SPJ11
a track star runs a 405-m race on a 405-m circular track in 41 s. what is his angular velocity assuming a constant speed?
To find the angular velocity of the track star, we can use the formula:
Angular velocity (ω) = Δθ / Δt
Angular velocity (ω) = 2π radians / 41 s
Where:
Δθ is the change in angle
Δt is the change in time
In this case, the track star runs a complete lap around the circular track, which corresponds to a change in angle of 2π radians (a full circle). The time it takes to complete the race is 41 seconds.
Plugging these values into the formula, we have:
Angular velocity (ω) = 2π radians / 41 s
Calculating this value, we get:
ω ≈ 0.153 radians/s
Therefore, the angular velocity of the track star is approximately 0.153 radians/s. This indicates the rate at which the track star covers angular distance (in this case, the angle corresponding to one lap around the circular track) per unit of time.
Learn more about velocity here
https://brainly.com/question/80295
#SPJ11
In a physics lab, you attach a 0.200-kg air-track glider tothe end of an ideal spring of negligible mass and start itoscillating. The elapsed time from when the glider first movesthrough the equilibrium point to the second time it moves throughthat point is 2.60 s.
Find the spring's force constant.
Thanks so much in advance.
The spring's force constant is approximately 4.09 N/m. The force constant of the spring can be calculated using the given values. The detailed solution is given below.
To find the spring's force constant, we can use the equation:
T = 2π √(m/k)
where T is the period of oscillation, m is the mass of the glider, k is the spring constant.
We are given that the elapsed time from the first movement through the equilibrium point to the second time is 2.60 s. Since the period is the time for one complete oscillation, the period of oscillation is:
T = 2.60 s / 2 = 1.30 s
The mass of the glider is 0.200 kg.
Now we can substitute these values into the equation and solve for k:
1.30 s = 2π √(0.200 kg / k)
Squaring both sides and solving for k, we get:
k = (4π^2 * 0.200 kg) / (1.30 s)^2
k ≈ 4.09 N/m
Therefore, the spring's force constant is approximately 4.09 N/m.
To learn more about oscillation visit;
https://brainly.com/question/30111348
#SPJ11
in the center of the dinner plate is a carrot slice of mass 10.2 g . if the carrot slice is just on the verge of slipping at the end point of the path, what is the coefficient of static friction between the carrot slice and the plate? take the free fall acceleration to be 9.80 m/s2 .
Ff = μs * Fn
the coefficient of static friction between the carrot slice and the plate is 1.where Ff is the force of friction, μs is the coefficient of static friction, and Fn is the normal force.
the force of friction is equal to the force pushing the carrot slice towards the edge of the plate
This force is equal to the gravitational force acting on the carrot slice:
Ff = m * g
where m is the mass of the carrot slice and g is the acceleration due to gravity (9.80 m/s2).
Substituting in the values we have:
Ff = 10.2 g * 9.80 m/s2
Ff = 99.96 g
where g is the gravitational acceleration.
The normal force is equal to the weight of the carrot slice:
Fn = m * g
Substituting in the values we have:
Fn = 10.2 g * 9.80 m/s2
Fn = 99.96 g
Now we can use the formula for friction to find the coefficient of static friction:
Ff = μs * Fn
99.96 g = μs * 99.96 g
μs = 1
the coefficient of static friction between the carrot slice and the plate is 1.
to know more about coefficient visit
https://brainly.com/question/30845099
#SPJ11
for a 250 kg vehicle without spoilers, where the coefficient of friction is measured at 0.8, what is the approximate maximum lateral force on the vehicle during a turn?
The approximate maximum lateral force on the vehicle during a turn is approximately 1960 Newtons.
To calculate the approximate maximum lateral force on a vehicle during a turn, you can use the equation:
F_max = μ * N,
where F_max is the maximum lateral force, μ is the coefficient of friction, and N is the normal force acting on the vehicle.
The normal force, N, can be calculated as the product of the mass of the vehicle (m) and the acceleration due to gravity (g):
N = m * g,
where m is the mass of the vehicle and g is approximately 9.8 m/s^2.
Given that the mass of the vehicle is 250 kg and the coefficient of friction is 0.8, we can calculate the maximum lateral force as follows:
N = 250 kg * 9.8 m/s^2 = 2450 N
F_max = 0.8 * 2450 N ≈ 1960 N
To know more about gravity, visit:
https://brainly.com/question/31321801
#SPJ11
Please Explain This!
Based on the information, we can infer that the image shows a car that fell into a hole in the road.
What is shown in the image?The image shows a car that is inside a hole in the road. Generally these situations occur when the roads are on unstable ground where holes are naturally formed.
In this case, the car falls into the hole because the asphalt gives way to the unstable ground and breaks, causing holes to form in the road. Therefore, engineers must correctly study the characteristics of the terrain to avoid these problems.
Learn more about accidents in: https://brainly.com/question/1235714
#SPJ1
a high-energy beam of alpha particles collides with a stationary helium gas target. part a what must the total energy of a beam particle be if the available energy in the collision is 16.4 gevgev ?
We can see here that the total energy of a beam particle must be at least 16.4 GeV.
What is energy?The ability of a system to perform work or bring about change is referred to as energy, which is a fundamental term in physics. It has magnitude but no clear direction because it is a scalar quantity.
We got the above answer in the following way:
Available energy = 16.4 GeV
Energy of target particle = 0 GeV
Energy of beam particle = ?
Energy of beam particle = Available energy - Energy of target particle
Energy of beam particle = 16.4 GeV - 0 GeV
Energy of beam particle = 16.4 GeV
This is because the available energy in the collision is 16.4 GeV, and the energy of the beam particle must be greater than or equal to the energy of the target particle.
Learn more about energy on https://brainly.com/question/25959744
#SPJ1
simple harmonic motion: if the amplitude of the motion of a simple harmonic oscillator is doubled, by what factor does the maximum speed of the oscillator change? simple harmonic motion: if the amplitude of the motion of a simple harmonic oscillator is doubled, by what factor does the maximum speed of the oscillator change? 2 4 it does not change. 1/2 1/4
The factor by which the maximum speed changes when the amplitude is doubled is 2.
If the amplitude of the motion of a simple harmonic oscillator is doubled, the maximum speed of the oscillator changes by a factor of 2.
In simple harmonic motion, the maximum speed occurs at the equilibrium position, where the displacement is zero. The maximum speed is directly proportional to the amplitude of the motion.
When the amplitude is doubled, the oscillation reaches a larger maximum displacement from the equilibrium position. As the oscillator moves farther from the equilibrium, it accelerates, resulting in an increased maximum speed. Since the maximum speed is directly related to the amplitude, doubling the amplitude doubles the maximum speed.
Therefore, the factor by which the maximum speed changes when the amplitude is doubled is 2.
To know more about oscillation, refer here:
https://brainly.com/question/30111348#
#SPJ11
Estimate the moment of inertia of a bicycle wheel 70 cm in diameter. The rim and tire have a combined mass of 1.3kg . The mass of the hub can be ignored.
The moment of inertia of a solid disk is given by the formula: I = (1/2) * M * R^2
Diameter of the wheel = 70 cm
Radius of the wheel (R) = 70 cm / 2 = 35 cm = 0.35 m
Mass of the rim and tire (M) = 1.3 kg
where I is the moment of inertia, M is the mass of the disk, and R is the radius of the disk.
Given:
Diameter of the wheel = 70 cm
Radius of the wheel (R) = 70 cm / 2 = 35 cm = 0.35 m
Mass of the rim and tire (M) = 1.3 kg
Substituting the values into the formula, we can calculate the moment of inertia:
I = (1/2) * 1.3 kg * (0.35 m)^2
Calculating the expression will give us the moment of inertia of the bicycle wheel.
Learn more about inertia here
https://brainly.com/question/1140505
#SPJ11
A concrete play are is resurfaced with dark- colored asphalt. Compared with the amount of heat energy that was absorbed by the old concrete surface, the amount of energy absorbed by the dark- colored asphalt surphace will most probably be
The dark-colored asphalt surface will most probably absorb more heat energy than the old concrete surface due to its darker color and higher thermal conductivity.
This can lead to higher surface temperatures and potentially create an uncomfortable or unsafe environment for play. It is recommended to use lighter-colored or reflective surfaces for play areas to reduce heat absorption and prevent surface temperatures from becoming too hot. A concrete play area is resurfaced with dark-colored asphalt.
Compared with the amount of heat energy that was absorbed by the old concrete surface, the amount of energy absorbed by the dark-colored asphalt surface will most probably be: 1. Higher. The reason for this is that dark-colored surfaces, like the asphalt in this case, absorb more heat energy than lighter-colored surfaces, such as the old concrete. This is because dark colors absorb a larger portion of the incoming solar radiation, converting it into heat energy.
As a result, the dark-colored asphalt surface will absorb more heat energy than the old concrete surface.
To know more about heat energy visit -
brainly.com/question/29210982
#SPJ11
Investigators measure the size of fog droplets using the diffraction of light. A camera records the diffraction pattern on a screen as the droplets pass in front of a laser, and a measurement of the size of the central maximum gives the droplet size. In one test, a 690 nm laser creates a pattern on a screen 30 cm from the droplets. Part A If the central maximum of the pattern is 0.26 cm in diameter, how large is the droplet? Express your answer with the appropriate units. μΑ ? D- Value Units Submit Request Answer
The droplet size is approximately 0.00493 cm. To determine the size of the droplet, we can use the concept of diffraction and the relationship between the diameter of the central maximum and the wavelength of light.
The formula relating the diameter of the central maximum (D) to the wavelength of light (λ) and the distance from the screen to the droplets (L) is given by: D = (2 * λ * L) / d
Where:
D is the diameter of the central maximum (0.26 cm),
λ is the wavelength of light (690 nm or 6.9 × [tex]10^{-5}[/tex] cm),
L is the distance from the screen to the droplets (30 cm), and
d is the size of the droplet we want to find.
Rearranging the formula, we can solve for d: d = (2 * λ * L) / D. Substituting the given values: d = (2 * 6.9 ×[tex]10^{-5}[/tex] cm * 30 cm) / 0.26 cm. Calculating the value, we find: d ≈ 0.00493 cm
The droplet size is approximately 0.00493 cm.
To know more about diffraction, refer here:
https://brainly.com/question/1812927#
#SPJ11