Answer:
Intake, compression, power, and exhaust
Explanation:
A four-stroke cycle engine is an internal combustion engine that utilizes four distinct piston strokes (intake, compression, power, and exhaust) to complete one operating cycle. The piston make two complete passes in the cylinder to complete one operating cycle.
The sequence of a single complete engine cycle is Intake, compression, power, exhaust. Therefore option 1 is correct.
1. Intake: In this step, the intake valve opens, allowing a mixture of air and fuel to enter the combustion chamber.
2. Compression: After the intake stroke, the intake valve closes, and the piston moves back up, compressing the air-fuel mixture. This compression increases the pressure and temperature inside the cylinder, preparing it for combustion.
3. Power: Once the air-fuel mixture is compressed, the spark plug ignites it. The burning mixture rapidly expands, generating a high-pressure force that pushes the piston down.
4. Exhaust: After the power stroke, the exhaust valve opens, and the piston moves back up, pushing the burned gases out of the cylinder and into the exhaust system.
Know more about engine cycle:
https://brainly.com/question/32297821
#SPJ2
Q24. List all of the ways you can force the reaction to shift to the product 5 points
side. (There are 5 ways total)
Answer:
1) Increase temperature
2) Decrease temperature
3) Increase concentration of reactants
4) Increase pressure
5) Decrease pressure
Explanation:
Le Chatelier's Principle Fundamentals states that a chemical reaction at equilibrium that undergoes changes to pressure, temperature, or concentration, this will cause the equilibrium to shift in the opposite direction to offset the change.
1) Increase temperature
2) Decrease temperature
3) Increase concentration of reactants
4) Increase pressure
5) Decrease pressure
For neon, determine the moles and mass contained in a 29.9−L volume at a pressure of 481.1 torr at a temperature of 300.0 K.
Answer:
.7689 mol
15.516 g
Explanation:
Use the Ideal Gas Law, PV = nRT.
Make sure to use the correct ideal gas constant R. You can either put R in torr, or you can change the pressure to atm. I've just used the torr ideal gas constant.
481.1 torr * 29.9 L = n 62.364 LTorr/molK * 300 K
14384.89 = 18709.2n
n = .7689 mol
The molar mass of neon (remember that neon gas = Ne, it's not diatomic) is 20.18 g/mol from the periodic table.
.7689 mol * 20.18 g/mol = 15.516 g
Which ion below is present in greatest concentration in a basic (alkaline) solution
Answer:
hydroxide ion / OH-
Explanation:
Basic solutions have a greater concentration of hydroxide ions than hydrogen (H+) ions
The topmost layer of the Earth is made up of large pieces that fit together like a puzzle. However, these pieces don't stay still, and sometimes they rub against each other. When these large sections of the Earth’s crust, called tectonic plates, hit each other, they send vibrations through the surface of the Earth. These vibrations are seismic waves. Seismic waves are just like the ripples in a pond. But instead of traveling through water, they travel through the Earth. When they reach the Earth's surface, they make the ground shake. That's an earthquake.
Earthquakes are the result of?
A ripples traveling through water.
B Earth’s topmost layer sinking.
C vibrations from seismic waves.
D tectonic plates staying still.
Answer:
C- vibrations from seismic waves
Answer:
C vibrations from seismic waves.
Explanation:
The shifting rock in an earthquake causes vibrations called seismic waves.
.
Showing a correct numerical setup, determine the percent composition by mass of carbon in baking soda (gram-formula mass - 84 grams per mole).
Answer:
Percentage Mass carbon = 14.3%
Explanation:
Baking soda which is sodium hydrogen bicarbonate has the molecular fomula, NaHCO3.
Atomic masses of each of the component atoms is, Na = 23; H = 1; C = 12; O = 16
Step 1: Molar mass of NaHCO3 = 23 + 1 + 12 + 3*16 = 84 g/mol
Step 2: Percentage mass of Carbon = (atomic mass of Carbon / molar mass of NaHCO3) * 100%
= (12 / 84) *100%
Percentage Mass of carbon = 14.3%
9. What is the difference between physical weathering and chemical weathering?
Answer: Physical Weathering physically breaks the rock, while Chemical Weathering chemically changes the rock causing it to break.
Explanation: Physical Weathering happens naturally causing the rock to break. An example is roots growing into the concrete causing it to crack. Chemical Weathering on the other hand chemically changes the rock by a chemical reaction. An example is acid rain. Gas or other pollution mixing in with water causing acid rain.
hope this helps ;)
The picture represents _________________.
A . Compounds
B . Mixture of Elements and Compounds
C. Mixture of Elements
D. Elements
E. Mixture of Compounds
What is the mass of two moles of HNO3?
Answer:
126 grams
Explanation:
What is the mass of two moles of HNO3?
H = 1g/mole = 1+
N = 14g/mole = 3-
O = 16g/mole = 2-
HNO3 = 63g/mole
What is one way in which chemistry affects your everyday life?
A. Refrigerators use energy more efficiently than they did 10 years
ago.
B. Tap water is safe to drink because it is monitored for harmful
substances.
c. Weather forecasts are now more accurate because of radar.
D. Watches are now more accurate because they are digitalized.
Answer: B
Explanation: Water is filtered with a bunch of chemicals which makes it drinkable.
What determines the average kinetic energy of the particles in a gas?
A.
the number of collisions
B.
the number of particles
OC.
the size of the particles
D.
the temperature
Answer:
D
The temperature.
Explanation:
explain how redox reactions are the source of electron flow in batteries. how can a dead battery be said to have attained equilibrium?
Answer:
can u help me whith one of my qutions
Explanation:
WILL MARK BRAINLIEST IF CORRECT
Calculate the average rate of change for the graphed sequence from n = 1 to n = 3. graphed sequence showing point 1, 2, point 2, 4, point 3, 8, point 4, 16, point 5, 32, and point 6, 64
A. 1
B. 2
C. 3
D. 6
Answer:it b
Explanation:
I've done that before
Answer:
The Answer is C or 3
Explanation:
I took the test
Which equation represents neutralization?
6Li(s) + N2(g) → 2Li3N(S)
2Mg(s) + O2(g) → 2MgO(S)
2KOH(aq) + H2SO4(aq) → K2SO4(aq) + 2H2O(l)
Pb(NO3)2(aq) + K2CrO4(aq) → 2KNO3(aq) PbCrO4(s)
Answer:
2KOH(aq) + H2SO4(aq) → K2SO4(aq) + 2H2O(l)
Explanation:
A neutralization reaction refers to any reaction between an acid and a base to form salt and water only. In a neutralization reaction, the key reaction that takes place to produce water is shown ionically below;
H^+(aq) +OH^-(aq) ----> H2O(l)
Looking at all the options provided, our gaze will have to settle on the reaction;
2KOH(aq) + H2SO4(aq) → K2SO4(aq) + 2H2O(l)
We can clearly see that there is an acid that reacts with a base to form a salt and water. The base contains the OH^- ion while the acid contains the hydrogen ion.
This is the only reaction of this sort among the options hence it is the correct answer.
How many hours will it take for only 1.5625 mg to remain
Answer:
36 hours
Explanation:
Notice that you are given the actual table of how the isotope reduces , and it shows that for each period of 6 hours the isotope decays to half of the initial number.
EVery 6 hours, the reduction in number of mg of the isotope goes down in half'
100 mg, then 50 mg, then 25 mg, then 12.5 mg, then 6.25 mg, then 3.125 mg and finally (reaching 1.5625 mg
That was 6 periods of 6 hours each, which totals: 6 time 6 hours = 36 hours
Label the following ph paper color as either strong / weak acid, strong/weak base, or neutral
1. neutral
2.strong base
3.weak acid
4.strong acid
5.weak base
Pls help I’m dying plssssssdsssss
Answer:
number 3
Explanation:
2 The precipitate formed when sodium hydroxide reacts with solutions
containing metal ions is the corresponding METAL HYDROXIDE.
a Write word equations and symbol equations including state symbols)
to show how the following solutions react with sodium hydroxide:
magnesium sulfate, MgSO4
ii iron(II) sulfate, FeSO4
ili iron(III) chloride, FeCl3
iv copper(ll) chloride, CuCl2
Answer:
Explanation:
MgSO4 + 2NaOH -------> Mg(OH)2 + 2NaSO4
CuCl2 +2NaOH -------> Cu (OH)2 + 2Nacl
FeCl3 + 3NaOH ----> Fe(OH)3 + 3NaCl
based on this can you try for the FeSO4. similar to first reaction showed above
mixture of 75 cm3of oxygen and 12.5 cm3 of a gaseous hydrocarbon H were exploded in an eudiometer. After cooling to room temperature, 50 cm3 of gas was left and when this was shaken with KOH solution, 12.5 cm3 of oxygen remained. Given that all the volumes were measured at same temperature and pressure, calculate the molar mass of the hydrocarbon H.
Answer:
molar mass of C₃H ₈ = 44 g/mole
Explanation:
Computation of the amount of oxygen that reacts .
⇒ 75 - 12.5
⇒ 62.5 cm³
Computation of proportion of hydrocarbons
2 mole hydrocarbons 3n+1 oxygen
⇒ 3 n + 1 = [62.5 × 2] / 12.5
⇒ 3 n + 1 = 10
⇒ n = 3
So,
Formula of the hydrocarbon is C₃H ₈
Computation of molar mass of C₃H ₈
⇒ [12×3] + [1×8]
⇒ 44 g/mole
Calculating pH
DETERMINE THE PH OF EACH SOLUTION
» [H] = 1 x 10-9M
pH =
» POH = 3
pH =
» [OH ) = 1 x 10-2 M
pH =
» POH = 7
pH =
Answer:
The answer to your question is given below
Explanation:
1. Data obtained from the question include:
Hydrogen ion concentration, [H+] = 1x10^-9M
pH =..?
pH = - log [H+]
pH = - log 1x10^-9
pH = 9
2. Data obtained from the question include:
pOH = 3
pH =.?
Recall:
pH + pOH = 14
pH + 3 = 14
Collect like terms
pH = 14 - 3
pH = 11
3. Data obtained from the question include:
Hydroxide ion concentration, [OH-] = 1x10^-2M
pH =..?
First, we shall determine the pOH. This is illustrated below
pOH = - Log [OH-]
pOH = - Log 1x10^-2
pOH = 2
Finally, we can obtain the pH as follow:
pH + pOH = 14
pOH = 2
pH + 2 = 14
Collect like terms
pH = 14 - 2
pH = 12
4. Data obtained from the question include:
pOH = 7
pH =.?
Recall:
pH + pOH = 14
pH + 7 = 14
Collect like terms
pH = 14 - 7
pH = 7
_________ is a jellylike substance within cells.
Answer:
Cytoplasm
Explanation:
Cytoplasm is a jellylike substance within cells.
Answer: he is right
Explanation:
do rainforests have hot summers and cold winters?
Answer:
No, rainforests have long wet winters and short dry summers.
What is the oxidation number of Si
Answer:
0
Explanation:
Neutrons are in the nucleus of the atom. A neutron has
a) A positive charge
b) No charge
c) A negative charge
d) Twice as much positive charge as a proton
Answer: B. (No charge)
Explanation:
Protons have a positive charge, electrons have a negative charge.
Neutrons are neutral and therefore have no change.
Neutralization Reactions
PREDICT THE PRODUCTS OF THE FOLLOWING REACTIONS
+
HNO3+ Ba(OH)2
+
H3PO4 + Ca(OH)2
→
Answer:
2HNO3+ Ba(OH)2 = Ba(NO3)2 + 2H2O
H3PO4 + Ca(OH)2 = Ca3(PO4)2 + 6H2O
Explanation:
2HNO3+ Ba(OH)2 = Ba(NO3)2 + 2H2O
H3PO4 + Ca(OH)2 = Ca3(PO4)2 + 6H2O
H+
O2-
OH-
Ba2+
Ca2+
NO3-
P 5+, 3+, 3-
H2O
What are substances on the right side of a chemical equation
called?
a. reactants
b. groups
C. products
d. electrons
Answer:
The substances on the right side of a chemical equation are the products as reactions typically move from left to right.
A chemical equation is a representation of chemical reaction in the form of symbols and formulae where the reactants are on left side and the products on right side.
Eg. CaCO3(s)→CaO(s)+CO2(g
What is chemical equation?Chemical equation is written "with the reactants on the left side of an arrow and the products of the chemical reaction on the right".
What is a reactant?Reactants are "the starting materials in a chemical reaction".
What is a product?
A product is "a chemical species resulting from a chemical reaction".
Hence, the substances on the right side of a chemical equation are products.
To learn more about chemical equation here
https://brainly.com/question/16783663
#SPJ2
I'll give brainliest
In going through the three physical states of matter, water would normally undergo changes in
A) composition.
B) density.
C) mass.
D) weight.
Answer:
COMPOSITION
Explanation:
Brainliest plz
Which is the best summary of the kinetic theory?
A. Potential energy is converted to kinetic energy.
O B. Atomic motion is constant at all temperatures.
C. Atoms and molecules are always in motion.
O D. Energy cannot be created or destroyed.
SUBMI
Answer:
C. Atoms and molecules are always in motion.
please help me!!!!!!!! if the temperature of your ice is 32 percent Fahrenheit and your water is 68 Fahrenheit and you mixed the ice and the water together what temperature is your water?
Answer:
36 degrees farenheit
1.
A car tire was inflated to 75 kPa at the repair shop where the
temperature is 15 °C. What is the pressure of the tire on the trip home
if the temperature of the road surface is 32 °C? (Write your answer
nearest whole number)
kPa
Answer:
THE PRESSURE OF THE TIRE ON THE TRIP HOME AT THE ROAD SURFACE TEMPERATURE OF 32°C IS 160 kPa.
Explanation:
Initial Pressure = 75 kPa
Initial temperature = 15 °C
Final temperature = 32 °C
Final pressure = unknown
Using the combined equation of gases;
P1V1/T1 = P2V2/ T2
Since the tire will have the same volume of air in it showing that volume of constant both at the repair shop and on the road surface.
The relationship between pressure and temperature is used with constant volume.
P1/T1 = P2/ T2
75 kPa / 15 °C = P2 / 32 °C
P2 = 75 kPa * 32 °C / 15 °C
P2 = 2400 kPa °C / 15 °C
P2 = 160 kPa.
So therefore, the pressure of the tire on the trip home when the temperature of the road surface is 32°C is 160 kPa.
How are electrons and positrons the same, and how are they different?
Answer:
A positron is the antimatter counterpart of an electron (also called anti-electron). ... The spin, a type of angular momentum carried by the electron and positron, is the same for both. However, the electron and positron have the opposite charge. The electron has a negative charge, and the positron has positive charge.