Answer: Last week, Nate and I counted all the inventory.
Explanation: all other choices are passive voices
this sentence follows a clear subject + verb + object construct that's why it is an active voice. In fact, sentences constructed in the active voice add impact to your writing. but on the other hand With passive voice, the subject is acted upon by the verb.
Ape x
Answer:
Last week, Nate and I counted all the inventory.
Explanation:
According to the
simple machine below, which part of the system is
considered the resistance force? *
2 points
A
B
Answer:
The part of the system that is considered the resistance force is;
B
Explanation:
The simple machine is a system of pulley that has two pulleys
The effort, which is the input force at A gives the value of the tension at C and D which are used to lift the load B
Therefore, we have;
A = C = D
B = C + D = C + C = 2·C
∴ C = B/2
We have;
C = B/2 = A
Therefore, with the pulley only a force, A equivalent to half the weight, B, of the load is required to lift the load, B
The resistance force is the constant force in the system that that requires an input force to overcome in order for work to be done
It is the force acting to oppose the sum of the other forces system, such as a force acting in opposition to an input force
Therefore, the resistance force is the load force, B, for which the input force, A, is required in order for the load to be lifted.
When Hailey participated in a tree plantation drive, she wore her most comfortable loungewear. However, the same attire was not acceptable at her workplace. Why?
Hailey’s attire was not acceptable because...
1. Her attire was not neat or clean
2. Her attire was not
appropriate for her profession
3. She wore the wrong outfit for the tree plantation drive
4. Her colleagues were just jealous of her attire
A substance that produces a lot of heat on burning is called
Answer:
A substance that produces a lot of heat on burning is called;
Fuel
Explanation:
A fuel can be described as a material that can release energy such as heat energy or work when it is reacted with other material for example the reaction involving fuel substances such as, gas, wood, oil, or coal, and oxygen during burning (combustion) that produces heat energy, power and light.
During mechanical cleaning, the container should be grounded to
minimize the possibility of static charge buildup and spark
True
O False
PLZ ASAP WILL GIVE BRAINLIST
Click this link to view O*NET’s Work Activities section for Personal Financial Advisors. Note that common activities are listed toward the top, and less common activities are listed toward the bottom. According to O*NET, what are some common work activities performed by Personal Financial Advisors? Check all that apply.
interacting with computers
making decisions and solving problems
evaluating information
performing general physical activities
handling and moving objects
getting information
Answer: A, B, C & F (interacting w computers, making decisions & solving problems, evaluating information & getting information).
Explanation: Those are the correct & verified answers.
Answer:
a b c f
Explanation:
is correct edge 2021
Hope this helps!
What is a building? Peeps I need help
A building is a building
i like the tree in the background my dear child
-Pilar
In the pressure filled driving environment, handicapping yourself by drinking and driving is not a good choice.
a) true
b) false
Answer:
True
Explanation:
Please mark me brainlist
Technician A says a solenoid is not used on modern automobiles. Technician B says fuel injectors and starter motor solenoids are two of many solenoids used on automobiles. Who is correct?
Select one
A Technician A
B. Technician B
C Both Techs A and B
Answer:
ON THE BOTTOM
Explanation:
red cord plus black cord
Can you give me examples of reciprocating motion?
Answer:
Other examples of reciprocating motion include piston pumps and compressors, roller pressure and tensioning systems, material testing devices, and insertion machines.
Explanation:
Please help me with this. Plzzz.
Answer:
450,000m = 450km = 4.5E5
32,600,000W = 32.6MW = 3.26E7
59,700,000,000cal = 59.7Gcal = 5.97E10
0.000000083s = 83ns = 8.3E-8
35,000Ω = 35kΩ = 3.5E4
Explanation:
Giga = 1,000,000,000
Mega = 1,000,000
kilo = 1,000
unit = 1
deci = .1
centi = .01
milli = .001
micro = .000001
nano = .0000000001
pico = .000000000001
You should be able to look at these and convert between them in seconds if you want to pursue anything in engineering.
A quantity of gas has a pressure of 1.39 atm and a volume of 6.95 L. What is the
volume of this gas when the pressure is changed to 740 mm Hg?
Answer:
The volume of the quantity of gas when the pressure changes to 740 mm Hg is approximately 9.92 L
Explanation:
The properties of the quantity of gas are;
The initial pressure of the gas, P₁ = 1.39 atm
The initial volume of the given volume of gas, V₁ = 6.95 L
The final pressure of the quantity of gas, P₂ = 740 mmHg
Boyle's Law states that at constant temperature, the pressure, P, of a given mass of gas is inversely proportional to its volume, V
Mathematically Boyle's Law can be written as follows;
[tex]P \propto \dfrac{1}{V}[/tex]
Therefore, we have;
P₁·V₁ = P₂·V₂
Where;
V₂ = The final volume of the quantity of gas when the pressure changes to 740 mm Hg
[tex]\therefore V_2 = \dfrac{P_1 \cdot V_1}{P_2}[/tex]
By substituting the known values, we have;
[tex]V_2 = \dfrac{1.39 \ atm \times 6.95 \ L}{740 \ mmHg} = \dfrac{1.39 \ atm \times 6.95 \ L}{0.973521 \ atm} = 9.92159459459 \ L \approx 9.92 \ L[/tex]
The final volume of the quantity of gas when the pressure changes to 740 mm Hg = V₂ ≈ 9.92 L
Someone who has the knowledge and experience to handle problems is a
Jeff is currently working at a construction site for a shopping mall. His job is to determine labor costs and negotiate prices of various raw materials from different contractors. What is Jeff's designation?
a. Coordinator
b. Estimator
c. Superintendent
d. Surveyor
Answer:
b. Estimator
Explanation:
Question: 10 of 15
QUESTION:
Which of the following determines the size of a fillet weld?
POSSIBLE ANSWERS:
O Crown height
O Leg length
O Porosity
O Root opening width
Submit Answer
Skip Question
Answer:
Leg length
Explanation:
The distances from the root to the edges of the legs (toes) and the height of the crown are basic measurements.
Find the mechanical average of a wheel axle System of the wheel has a radius of 1.5 feet in the accident has a radius of 6 inches if the force is put on a axle
Answer:
Mechanical average of a wheel = 3
Explanation:
Given:
Radius of wheel = 1.5 ft = 1.5 x 12 = 18 inches
Radius of axle = 6 inches
Find:
Mechanical average of a wheel
Computation:
Mechanical average of a wheel = Radius of wheel / Radius of axle
Mechanical average of a wheel = 18 / 6
Mechanical average of a wheel = 3
What are some goals of NYFEA? Select three options.
encouraging political involvement
educating children
developing agricultural leaders
encouraging new and young farmers
developing medical treatments
encouraging small farms
Answer:
developing agricultural leaders
encouraging new and young farmers
encouraging small farms
Answer:
3
4
6
Explanation:
what are the different types of documents used to communicate engineering designs?
Answer:
COMMON ENGINEERING DOCUMENTS
Inspection or trip reports.
Research, laboratory, and field reports.
Specifications.
Proposals.
Progress reports.
ect...
Explanation:
product innovation is driven by what?
Answer:
Market
Competition
Products innovation strategy
What are examples of Quality Assurance workplaces? Check all that apply.
laboratories
vehicles
design studios
factories
stores
offices
Answer: laboratories, factories, offices
Explanation:
Answer:
b and on edg
Explanation:
and have a good day
Before applying any kind of glue, all of the parts should first be assembled and the fit of joints and other attachments carefully checked. This operation is generally called a __
Answer:
Trial assembly.
Explanation:
Trial assembly can be defined as a strategic process which typically involves assembling the parts of a product to ensure that they perfectly fit.
Before applying any kind of glue, all of the parts should first be assembled and the fit of joints and other attachments carefully checked. This operation is generally called a trial assembly.
The main purpose of a trial assembly is to eliminate errors or mistakes before the permanent assemblage of a product and to ensure that the structure of a finished (end) product matches with the design model or prototype.
Which of the following describes what should happen before a home is designed?
Answer:
A
Explanation:
In a solar cell, solar energy is converted to
What kind of energy?
Answer:
Renewable energy. Have a good day.
Answer:It Is converted into electric energy
Explanation:because solar panal use solar energy
________ are written to “maximize” or “minimize” a specific value associated with the product needs in order to define the goal or aim of the design process.
Answer:
Objective statements.
Explanation:
An objective statement can be defined as a short statement that explicitly states or describes what a person wants exactly or is looking out for in a particular item.
Objective statements are written to “maximize” or “minimize” a specific value associated with the product needs in order to define the goal or aim of the design process.
This ultimately implies that, objective statements are used by various manufacturing industries or companies to explicitly define the minimum or maximum requirements for the production of its goods.
Answer:
B
Explanation:
A car battery is a 12V DC source. Typically you will find a fuse that can handle a 7 amp surge to power on the lights in your car. What resistance is that fuse protecting?*'
Answer:
resistance=power/current=12/7=1.71ohm
the manufacturer specifies that a terminal lug be torqued to 7.5 foot-lbs but your to calibrated in inch-pounds, you would set your wrench at in. Ib. Select one O a. 90 O b. 1.6 O c. 7.5 O d. 37.5 e kone of these