Answer:
(a) v = 13.13 m/s
(b) The centrifugal force balances the force of the road, so net force is zero.
(c) v = 13.13 m/s
(d) v = 18.92 m/s
Explanation:
(a)
To make it around the turn without skidding the frictional force on cat must balance the centrifugal force. Therefore:
Frictional Force = Centrifugal Force
μR = mv²/r
where,
R = Normal Reaction = Weight of Car = mg
Therefore,
μmg = mv²/r
μg = v²/r
v = √μgr
where,
v = maximum possible velocity of car = ?
μ = coefficient of friction = 0.22
g = 9.8 m/s²
r = radius of curvature = 80 m
Therefore,
v = √[(0.22)(9.8 m/s²)(80 m)
v = 13.13 m/s
(b)
In order for the car to move without skidding around the turn, all the forces in horizontal direction must be equal. Hence, the centrifugal force and the frictional force (force of the road) must balance each other. So the true statement is:
The centrifugal force balances the force of the road, so net force is zero.
(c)
v = √μgr
Since the formula for speed is independent of mass. Therefore, the speed will remain same.
v = 13.13 m/s
(d)
v = √μgr
v = √[(0.22)(9.8 m/s²)(166 m)
v = 18.92 m/s
A 9.0-V battery (with nonzero resistance) and switch are connected in series across the primary coil of a transformer. The secondary coil is connected to a light bulb that operates on 120 V. Determine the ratio of the secondary to primary turns needed for the bells transformer. Determine the ratio of the secondary to primary turns needed for the bells transformer. Ns/Np=?
Answer:
N₂ / N₁ = 13.3
Explanation:
A transformer is a system that induces a voltage in the secondary due to the variation of voltage in the primary, the ratio of voltages is determined by the expression
ΔV₂ = N₂ /N₁ ΔV₁
where ΔV₂ and ΔV₁ are the voltage in the secondary and primary respectively and N is the number of windings on each side.
In this case, they indicate that the primary voltage is 9.0 V and the secondary voltage is 120 V
therefore we calculate the winding ratio
ΔV₂ /ΔV₁ = N₂ / N₁
N₂ / N₁ = 120/9
N₂ / N₁ = 13.3
s good clarify that in transformers the voltage must be alternating (AC)
What caused the disappearance of land bridges?
A. Volcanic outgassing
B. Shrinking of the polar ice caps
C. Beginning of an ice age
D. A mass extinction
Answer: B
Explanation:
I would say the shrinking of the polar ice caps because in order for ice caps to shrink, they would have to obviously melt. This will cause the sea level and total volume of sea water to rise and cover up the land bridges
Answer:B :)
Explanation:
Write the first equation of motion. Under what condition(s) is this equation valid?
Explanation:
The first equation of motion in kinematics is given by :
[tex]v=u+at[/tex] .....(1)
u is initial speed
a is acceleration
v is final speed
t is time
Equation (1) is valid when the object is moving with constant acceleration. This equation gives relation between velocity and time.
A 328-kg car moving at 19.1 m/s in the x direction hits from behind a second car moving at 13.0 m/s in the same direction. If the second car has a mass of 790 kg and a speed of 15.1 m/s right after the collision, what is the velocity of the first car after this sudden collision
Answer:
14.04 m/s
Explanation:
To find the velocity of the first car after the collision, we can use the equation of conservation of momentum:
m1v1 + m2v2 = m1'v1' + m2'v2'
We have the following data:
m1 = m1' = 328,
m2 = m2' = 790,
v1 = 19.1,
v2 = 13,
v2' = 15.1.
Using this data, we can find v1' (final velocity of the first car):
328 * 19.1 + 790 * 13 = 328 * v1' + 790 * 15.1
16534.8 = 328 * v1' + 11929
328 * v1' = 4605.8
v1' = 14.04 m/s
A conducting sphere contains positive charge distributed uniformly over its surface. Which statements about the potential due to this sphere are true? All potentials are measured relative to infinity
a. The potential at the center of the sphere is zero.
b.The potential is lowest, but not zero, at the center of the sphere.
c. The potential at the center of the sphere is the same as the potential at the surface.
d. The potential at the center is the same as the potential at infinity.
e. The potential at the surface is higher than the potential at the center.
Answer:
a. FALSE
b. FALSE
c. TRUTH
d. FALSE
e. FALSE
Explanation:
To determine which statements are truth or false you focus in the following formula, for the electric potential generated by a conducting sphere:
[tex]V=\frac{Q}{4\pi \epsilon_o R}[/tex] inside the sphere
[tex]V'=\frac{Q}{4\pi \epsilon_o r}[/tex] for r > R (outside the sphere)
R: radius of the sphere
ε0: dielectric permittivity of vacuum
Q: charge of the sphere
As you can notice, inside the sphere the potential is constant. Inside the sphere, the potential is the same. Outside the surface the potential decreases as 1/r, being r the distance to the center of the sphere.
Hence, you can conclude:
a. The potential at the center of the sphere is zero. FALSE
b.The potential is lowest, but not zero, at the center of the sphere. FALSE
c. The potential at the center of the sphere is the same as the potential at the surface. TRUTH
d. The potential at the center is the same as the potential at infinity. FALSE
e. The potential at the surface is higher than the potential at the center. FALSE
What is the power of a child that has
done work of 50J in 10 seconds.
(a)50W (b)20W (c)30W (d)5W
_____________________________
Solution,
Work=50 Joule
Time=10 seconds
Power=?
Now,
Power=Work/time
= 50/10
= 5 Watt.
So the right answer is 5 W
Hope it helps..
Good luck on your assignment
__________________________
Which of the following is analogous to the pipes in an electrical circuit?
A. capacitors storing the incoming charge from the battery
B. large resistors causing restrictions to the flow of charge
C. electric current flowing “downhill” from the negative electrode to the positive electrode in a battery electric current being forced uphill by the battery
D. electric current being forced uphill by the battery back to the positive terminal
The correct answer is D. electric current being forced uphill by the battery back to the positive terminal.
What is Electric Current?
Electric current is the flow of electric charge through a conducting medium, such as a wire, due to the movement of electrons or ions. The flow of charge is typically caused by the presence of an electric field that creates a potential difference (voltage) between two points in a circuit
In an electrical circuit, pipes are analogous to wires or conductive paths that allow the flow of electric current. The flow of electric current is from the positive terminal of the battery to the negative terminal, which is opposite to the direction of conventional current flow. Therefore, option C is incorrect.
Learn more about Electric Current
https://brainly.com/question/1100341
#SPJ1
¿Cuantos metros recorre una motocicleta en un segundo si circula a una velocidad de 90km/h?
Answer:
La motocicleta recorre 25 metros en 1 segundo si circula a una velocidad de 90 km/h
Explanation:
La velocidad es una magnitud que expresa el desplazamiento que realiza un objeto en una unidad determinada de tiempo, esto es, relaciona el cambio de posición (o desplazamiento) con el tiempo.
Siendo la velocidad es el espacio recorrido en un período de tiempo determinado, entonces 90 km/h indica que en 1 hora la motocicleta recorre 90 km. Entonces, siendo 1 h= 3600 segundos (1 h=60 minutos y 1 minuto=60 segundos) podes aplicar la siguiente regla de tres: si en 3600 segundos (1 hora) la motocicleta recorre 90 km, entonces en 1 segundo ¿cuánta distancia recorrerá?
[tex]distancia=\frac{1 segundo*90 km}{3600 segundos}[/tex]
distancia= 0.025 km
Por otro lado, aplicas la siguiente regla de tres: si 1 km es igual a 1,000 metros, ¿0.025 km cuántos metros son?
[tex]distancia=\frac{0.025 km*1,000 metros}{1 km}[/tex]
distancia= 25 metros
La motocicleta recorre 25 metros en 1 segundo si circula a una velocidad de 90 km/h
La cantidad de metros que recorre una motocicleta en un segundo si viaja a una velocidad de 90 km / h es de 25 m / s.
Para obtener la velocidad de la motocicleta en un segundo, necesitaremos convertir 90 km / h en metros por segundo
Usando la tasa de conversión;
1000 m = 1 km
1 hora = 3600 segundos
[tex]\frac{90km}{hr} = \frac{90km \times 1000 m}{1km \times 3600s} \\\\\frac{90km}{hr} = \frac{90,000 m}{3600s} =25m/s \\[/tex]
Esto muestra que la cantidad de metros que recorre una motocicleta en un segundo si viaja a una velocidad de 90 km / h es de 25 m / s.
Obtenga más información aquí: https://brainly.com/question/13136984
A ship can float on water as long as it weighs less than water.
O A. True
O B. False
Answer:
It's true
Explanation:
Because the ship is mafe up of aluminium, which is a light metal.
Answer:
False
Explanation:
Took The Quiz
When you "crack" a knuckle, you suddenly widen the knuckle cavity, allowing more volume for the synovial fluid inside it and causing a gas bubble suddenly to appear in the fluid. The sudden production of the bubble, called "cavitation", produces a sound pulse---the cracking sound. Assume that the sound is transmitted uniformly in all directions and that it fully passes from the knuckle interior to the outside, at a distance of 0.29 m from your ear. If the pulse has a sound level of 61 dB at your ear, what is the rate at which energy is produced by the cavitation
Answer:If a wave y(x, t) = (6.0 mm) sin(kx + (600 rad/s)t + Φ) travels along a string, how much time does any given point on the string take to move between displacements y = +2.0 mm and y = -2.0 mm?
Explanation:
Space-faring astronauts cannot use standard weight scales (since they are constantly in free fall) so instead they determine their mass by measuring the period of oscillation when sitting in a chair connected to a spring. Suppose a chair is connected to a spring with a spring constant of 600 N/m. If the empty chair oscillates with a period of 0.9s, what is the mass of an astronaut who oscillates with a period of 2.0 s while sitting in the chair
Answer:
ma = 48.48kg
Explanation:
To find the mass of the astronaut, you first calculate the mass of the chair by using the information about the period of oscillation of the empty chair and the spring constant. You use the following formula:
[tex]T=2\pi\sqrt{\frac{m_c}{k}}[/tex] (1)
mc: mass of the chair
k: spring constant = 600N/m
T: period of oscillation of the chair = 0.9s
You solve the equation (1) for mc, and then you replace the values of the other parameters:
[tex]m_c=\frac{T^2k}{4\pi^2}=\frac{(0.9s)^2(600N/m)}{4\pi^2}=12.31kg[/tex] (2)
Next, you calculate the mass of the chair and astronaut by using the information about the period of the chair when the astronaut is sitting on the chair:
T': period of chair when the astronaut is sitting = 2.0s
M: mass of the astronaut plus mass of the chair = ?
[tex]T'=2\pi\sqrt{\frac{M}{k}}\\\\M=\frac{T'^2k}{4\pi^2}=\frac{(2.0s)^2(600N/m)}{4\pi^2}\\\\M=60.79kg[/tex] (3)
Finally, the mass of the astronaut is the difference between M and mc (results from (2) and (3)) :
[tex]m_a=M-m_c=60.79kg-12.31kg=48.48kg[/tex]
The mass of the astronaut is 48.48 kg
To move a large crate across a rough floor, you push on it with a force at an angle of 15 degrees below the horizontal. Find the force necessary to start the crate moving, given that the mass of the crate is 32 kg and the coefficient of static friction between the crate and the floor is 0.49.
Answer:
663N
Explanation:
We need to find the force that will overcome the frictional force.
The angle of the normal force is 15°.
The mass of the crate is 32 kg
The coefficient of static friction is 0.49
Frictional force is given in terms of Normal force as:
F = μNcosθ
where μ = coefficient of static friction
N = normal force
θ = angle of normal force
Frictional force is given as:
F = mg
=>mg = μNcosθ
=> N = mg/(μcosθ)
N = (32 * 9.8) / (0.49 * cos15)
N= 313.6 / 0.473
N = 663 N
The force needed to cause the box to move must be 663N or greater.
The NASA spacecraft Deep Space I was shut down on December 18, 2001, following a three-year journey to the asteroid Braille and the comet Borrelly. This spacecraft used a solar-powered ion engine to produce 0.064 ounces of thrust (force) by stripping electrons from neon atoms and accelerating the resulting ions to 70,000 mi/h. The thrust was only as much as the weight of a couple sheets of paper, but the engine operated continuously for 16,000 hours. As a result, the speed of the spacecraft increased by 7900 mi/h. What was the mass of Deep Space I?
Answer:
The mass will be "8.86 lb".
Explanation:
The given values are:
Force
= 70,000 mi/h
Speed
= 7900 mi/h
On applying the Law of momentum, we get
⇒ [tex]V_{1}m_{1}=V_{2}m_{2}[/tex]
On putting the estimated values, we get
⇒ [tex]70000 = 7900\times mass \ of \ deepspace \ 1[/tex]
⇒ [tex]mass \ of \ deepspace \ 1 = \frac{70000}{7900}[/tex]
⇒ [tex]=8.86 \ lb[/tex]
A cantilever beam with a width b=100 mm and depth h=150 mm has a length L=2 m and is subjected to a point load P =500 N at B. Calculate the state of plane stress at point C located 50 mm below the top of the beam and 0.5 m to the right of point A. Also find the principal stresses and the maximum shear stress at C. Neglect the weight of the beam.
Answer:
Explanation:
Given that:
width b=100mm
depth h=150 mm
length L=2 m =200mm
point load P =500 N
Calculate moment of inertia
[tex]I=\frac{bh^3}{12} \\\\=\frac{100 \times 150^3}{12} \\\\=28125000\ m m^4[/tex]
Point C is subjected to bending moment
Calculate the bending moment of point C
M = P x 1.5
= 500 x 1.5
= 750 N.m
M = 750 × 10³ N.mm
Calculate bending stress at point C
[tex]\sigma=\frac{M.y}{I} \\\\=\frac{(750\times10^3)(25)}{28125000} \\\\=0.0667 \ MPa\\\\ \sigma =666.67\ kPa[/tex]
Calculate the first moment of area below point C
[tex]Q=A \bar y\\\\=(50 \times 100)(25 +\frac{50}{2} )\\\\Q=250000\ mm[/tex]
Now calculate shear stress at point C
[tex]=\frac{FQ}{It}[/tex]
[tex]=\frac{500*250000}{28125000*100} \\\\=0.0444\ MPa\\\\=44.4\ KPa[/tex]
Calculate the principal stress at point C
[tex]\sigma_{1,2}=\frac{\sigma_x+\sigma_y}{2} \pm\sqrt{(\frac{\sigma_x-\sigma_y}{2} ) + (\tau)^2} \\\\=\frac{666.67+0}{2} \pm\sqrt{(\frac{666.67-0}{2} )^2 \pm(44.44)^2} \ [ \sigma_y=0]\\\\=333.33\pm336.28\\\\ \sigma_1=333.33+336.28\\=669.61KPa\\\\\sigma_2=333.33-336.28\\=-2.95KPa[/tex]
Calculate the maximum shear stress at piont C
[tex]\tau=\frac{\sigma_1-\sigma_2}{2}\\\\=\frac{669.61-(-2.95)}{2} \\\\=336.28KPa[/tex]
A rifle fires a 2.05 x 10-2-kg pellet straight upward, because the pellet rests on a compressed spring that is released when the trigger is pulled. The spring has a negligible mass and is compressed by 8.01 x 10-2 m from its unstrained length. The pellet rises to a maximum height of 4.46 m above its position on the compressed spring. Ignoring air resistance, determine the spring constant.
Answer:
Spring Constant = 279.58 N/m
Explanation:
We are given;
Mass; m = 2.05 x 10^(-2) kg = 0.0205 kg
Distance of compression; x = 8.01 × 10^(-2) m = 0.0801 m
Maximum height; h = 4.46 m
The formula for the energy in the spring is given by;
E = ½kx²
where:
k is the spring constant
x is the distance the spring is compressed.
Now, this energy of the spring will be equal to the energy of the pellet at its highest point. Energy of pallet = mgh So;
½kx² = mgh
Plugging in the relevant values, we have;
½ * k * 0.0801² = 0.0205 * 9.81 * 4.46
0.003208005k = 0.8969
k = 0.8969/0.003208005
k = 279.58 N/m
1. Which of the following is NOT a vector quantity? (a) Displacement. (b) Energy. (c) Force. (d) Momentum. (e) Velocity.
Answer:
B. energy
Explanation:
A vector has direction.
Energy does not have a direction.
small car has a head-on collision with a large truck. Which of the following statements concerning the magnitude of the average force due to the collision is correct? A small car has a head-on collision with a large truck. Which of the following statements concerning the magnitude of the average force due to the collision is correct? It is impossible to tell since the velocities are not given. The truck experiences the greater average force. It is impossible to tell since the masses are not given. The small car and the truck experience the same average force. The small car experiences the greater average force.
Answer:
The correct option is D: "The small car and the truck experience the same average force."
Explanation:
The magnitude of the average force experienced by both bodies in motion is the same as explained by Newton's third law of motion. The force exerted by each body is equal and opposite in direction. The resulting acceleration experienced by each vehicle, however, will not be the same. It is greater for the small car.
To throw the discus, the thrower holds it with a fully outstretched arm. Starting from rest, he begins to turn with a constant angular acceleration, releasing the discus after making one complete revolution. The diameter of the circle in which the discus moves is about 1.7m. If the thrower takes 1.2s to complete one revolution, starting from rest, what will be the speed of the discus at release?
Answer:
4.437 m/s
Explanation:
Diameter of rotation d is 1.7 m
Radius of rotation = d/2 = 1.7/2 = 0.85 m
If he takes 1.2 sec to complete one revolution, then his angular speed is 1/1.2 = 0.83 rev/s
We convert to rad/s
Angular speed = 2 x pi x 0.83
= 2 x 3.142 x 0.83 = 5.22 rad/s
Speed is equal to the angular speed times the radius of rotation
Speed = 5.22 x 0.85 = 4.437 m/s
In the given case, the speed of the discus at release, If the thrower takes 1.2s to complete one revolution, starting from rest would be - 8.90 m/s.
Given:
diameter of the circle = 1.7 mradius f the circle would be = 1.7/2 = 0.85 m
time taken for one revolution t = 1.2 sThis rotation exercise can be treated using the rotation kinematics.
Angular acceleration:
θ = w₀ t + ½ α t²
t = 1.2 s to give a revolution (T = 2π rad) and with part of the rest the initial angular velocity is zero (wo = 0)
=> θ = 0 + ½ α t²
=> α = 2θ / t²
=> α= 2 × 2π / 1.2²
=> α = 4π = 8.7266 rad / s²
Let's calculate the angular velocity:
=> w = wo + α t
=> w = 0 + α t
=> w = 8.7266 × 1.2
=> w = 10.47192 rad / s
The relationship between linear and angular velocity is
=> r = d / 2
=> r = 1.7 / 2 = 0.85 m
=> v = w r
=> v = 10.47192 × 0.85
=> v = 8.90 m / s
Thus, the correct speed would be - 8.90 m/s
Learn more:
https://brainly.com/question/14663644
What is a substance?
first law of equilibrium
Answer:
for an object to be in equilibrium, it must be experiencing no acceleration. Both the net force and the net torque must be zero.
Hope I helped
Answer:
An object in static equilibrium has zero net force acting upon it.
The First Condition of Equilibrium is that the vector sum of all the forces acting on a body vanishes. This can be written as
F = F1+ F2+ F3+ F4+. . . = 0
A projectile is defined as
Answer:
By definition, a projectile has a single force that acts upon it - the force of gravity.
Explanation:
A projectile is any object that once projected or dropped continues in motion by its own inertia and is influenced only by the downward force of gravity.
// have a great day //
I really need help with this question someone plz help !
Answer:D
Explanation:
Given
Same force is applied to each ball such that all have different masses
and Force is given by the product of mass and acceleration
[tex]F=m\times a[/tex]
[tex]a=\frac{F}{m}[/tex]
So acceleration of ball A
[tex]a_A=\frac{F}{0.5}=2F[/tex]
acceleration of ball B
[tex]a_B=\frac{F}{0.75}=\frac{4F}{3}=1.33F[/tex]
acceleration of ball C
[tex]a_C=\frac{F}{1}=F[/tex]
acceleration of ball D
[tex]a_D=\frac{F}{7.3}=\frac{F}{7.3}[/tex]
It is clear that acceleration of ball D is least.
A ball is thrown upward from the ground with an initial speed of 19.2 m/s; at the same instant, another ball is dropped from a building 18 m high. After how long will the balls be at the same height above the ground?
Answer:
0.938 seconds
Explanation:
For the ball thrown upwards, we use the formula below to solve it:
[tex]s = ut - \frac{1}{2}gt^2[/tex]
where s = distance moved
u = initial speed = 19.2 m/s
t = time taken
g = acceleration due to gravity = 9.8 [tex]m/s^2[/tex]
Let x be the height at which both balls are level, this means that:
=> [tex]x = 19.2t - 4.9t^2[/tex]________(1)
For the ball dropped downwards, we use the formula below:
[tex]s = ut + \frac{1}{2}gt^2[/tex]
u = 0 m/s
At the point where both balls are level:
s = 18 - x
=> [tex]18 - x = 0 + 4.9t^2[/tex]
=> [tex]x = 18 - 4.9t^2[/tex]__________(2)
Equating both (1) and (2):
[tex]19.2t - 4.9t^2 = 18 - 4.9t^2\\\\=> 19.2t = 18\\\\t = 18/19.2 = 0.938 secs[/tex]
They will be level after 0.938 seconds
A 1000-kg car is driving toward the north along a straight horizontal road at a speed of 20.0 m/s. The driver applies the brakes and the car comes to a rest uniformly in a distance of 240 m. What are the magnitude and direction of the net force applied to the car to bring it to rest?
Answer:
The value of F= - 830 N
Since the force is negative, it implies direction of the force applied was due south.
Explanation:
Given data:
Mass = 1000-kg
Distance, d = 240 m
Initial velocity, v1 = 20.0 m/s
Final velocity, v2 = 0 (since the car came to rest after brake was applied)
v2²= v1² + 2ad (using one of the equation of motion)
0= 20² + (2 x a x 240)
0= 400 + 480 a
a = - 400/480
a = - 0.83 m/s²
Then, imputing the value of a into
F = ma
F = 1000 kg x ( - 0.83 m/s²)
F= - 830 N
The car was driving toward the north, and since the force is negative, it implies direction of the force applied was due south.
A flock of ducks is trying to migrate south for the winter, but they keep being blown off course by a wind blowing from the west at 5.0 m/s . A wise elder duck finally realizes that the solution is to fly at an angle to the wind.If the ducks can fly at 7.0 m/s relative to the air, what direction should they head in order to move directly south?
The ducks' flight path as observed by someone standing on the ground is the sum of the wind velocity and the ducks' velocity relative to the wind:
ducks (relative to wind) + wind (relative to Earth) = ducks (relative to Earth)
or equivalently,
[tex]\vec v_{D/W}+\vec v_{W/E}=\vec v_{D/E}[/tex]
(see the attached graphic)
We have
ducks (relative to wind) = 7.0 m/s in some direction θ relative to the positive horizontal direction, or[tex]\vec v_{D/W}=\left(7.0\dfrac{\rm m}{\rm s}\right)(\cos\theta\,\vec\imath+\sin\theta\,\vec\jmath)[/tex]
wind (relative to Earth) = 5.0 m/s due East, or[tex]\vec v_{W/E}=\left(5.0\dfrac{\rm m}{\rm s}\right)(\cos0^\circ\,\vec\imath+\sin0^\circ\,\vec\jmath)[/tex]
ducks (relative to earth) = some speed v due South, or[tex]\vec v_{D/E}=v(\cos270^\circ\,\vec\imath+\sin270^\circ\,\vec\jmath)[/tex]
Then by setting components equal, we have
[tex]\left(7.0\dfrac{\rm m}{\rm s}\right)\cos\theta+5.0\dfrac{\rm m}{\rm s}=0[/tex]
[tex]\left(7.0\dfrac{\rm m}{\rm s}\right)\sin\theta=-v[/tex]
We only care about the direction for this question, which we get from the first equation:
[tex]\left(7.0\dfrac{\rm m}{\rm s}\right)\cos\theta=-5.0\dfrac{\rm m}{\rm s}[/tex]
[tex]\cos\theta=-\dfrac57[/tex]
[tex]\theta=\cos^{-1}\left(-\dfrac57\right)\text{ OR }\theta=360^\circ-\cos^{-1}\left(-\dfrac57\right)[/tex]
or approximately 136º or 224º.
Only one of these directions must be correct. Choosing between them is a matter of picking the one that satisfies both equations. We want
[tex]\left(7.0\dfrac{\rm m}{\rm s}\right)\sin\theta=-v[/tex]
which means θ must be between 180º and 360º (since angles in this range have negative sine).
So the ducks must fly (relative to the air) in a direction 224º relative to the positive horizontal direction, or about 44º South of West.
Question 10
Air with a density of 1.20 kg/m3 flows through a 75.0 cm diameter pipe with a velocity of 2.00 m/s. What is the mass flow rate?
Answer:
75.0 cm
Explanation:
becouse i don,t no the right answer
Which of the following is NOT true about main sequence stars?
A.) The forces of gravity and nuclear fusion balance so the star does not collapse or explode.
B.) Temperature is directly related to brightness.
C.) The forces of gravity and nuclear fusion are not in balance so the star's core collapses while the outer layers expand.
D.) Temperature is related to size.
Answer:
the statements the B is not true
Explanation:
In the stars the force of gravity tends to collapse them, by joining the atoms nuclear reactions that create an outward force until the two forces reach an equilibrium
The temperature of a star is a reflection of the energy within it and it is related to the intensity of the nuclear rations and not to the size of the stars
In examining the statements the B is not true
How do you convert 1.3*10^6cal into joules
Answer:
5.4×10⁶J
Explanation:
1 cal = 4.184 J
1.3×10⁶ cal × (4.184 J/cal) = 5.4×10⁶J
A merry-go-round on a playground consists of a horizontal solid disk with a weight of 810 N and a radius of 1.56 m. A child applies a force 49.0 N tangentially to the edge of the disk to start it from rest. What is the kinetic energy of the merry-go-round disk (in J) after 2.95 s
Answer:
Kinetic Energy of the disk = 252 J
Explanation:
weight of disk = 810 N
radius = 1.56 m
applied force = 49 N
time = 2.95 s
kinetic energy of disk = ?
first, we find the mass of the disk
mass of disk = weight/acceleration due to gravity(9.81 m/s^2) = 810/9.81 m/s^2
mass of disk = 82.57 kg
torque on the disk = force x radius = 49 x 1.56 = 76.44 N-m
moment of inertia I = m[tex]r^{2}[/tex] = 82.57 x [tex]1.56^{2}[/tex] = 200.9 kg-[tex]m^{2}[/tex]
recall that
Torque T = Iα
where α = angular acceleration
76.44 = 200.9α
α = 76.44/200.9 = 0.38 m/s^2
from the equation of angular motion,
ω = ω' + αt
where ω = final angular speed
ω' = initial angular speed = 0 rad/s since disk starts from rest
t = time = 2.95 s
imputing values into the equation, we have
ω = 0 + (0.38 x 2.95)
ω = 1.12 rad/s
kinetic energy of the disk = I[tex]w^{2}[/tex]
KE = 200.9 x [tex]1.12^{2}[/tex]
Kinetic Energy of the disk = 252 J
A high diver of mass 60.0 kg steps off a board 10.0 m above the water and falls vertical to the water, starting from rest. If her downward motion is stopped 2.10 s after her feet first touch the water, what average upward force did the water exert on her
Answer:
The average upward force exerted by the water is 988.2 N
Explanation:
Given;
mass of the diver, m = 60 kg
height of the board above the water, h = 10 m
time when her feet touched the water, t = 2.10 s
The final velocity of the diver, when she is under the influence of acceleration of free fall.
V² = U² + 2gh
where;
V is the final velocity
U is the initial velocity = 0
g is acceleration due gravity
h is the height of fall
V² = U² + 2gh
V² = 0 + 2 x 9.8 x 10
V² = 196
V = √196
V = 14 m/s
Acceleration of the diver during 2.10 s before her feet touched the water.
14 m/s is her initial velocity at this sage,
her final velocity at this stage is zero (0)
V = U + at
0 = 14 + 2.1(a)
2.1a = -14
a = -14 / 2.1
a = -6.67 m/s²
The average upward force exerted by the water;
[tex]F_{on\ diver} = mg - F_{ \ water}\\\\ma = mg - F_{ \ water}\\\\F_{ \ water} = mg - ma\\\\F_{ \ water} = m(g-a)\\\\F_{ \ water} = 60[9.8-(-6.67)]\\\\F_{ \ water} = 60 (9.8+6.67)\\\\F_{ \ water} = 60(16.47)\\\\F_{ \ water} = 988.2 \ N[/tex]
Therefore, the average upward force exerted by the water is 988.2 N